background image

F D C 3 3 0 0   U s e r   M a n u a l

2

C H A P T E R   O N E

3

F D C 3 3 0 0   U s e r   M a n u a l

Free FLASH Upgrades

Firmware is stored in non-volatile FLASH memory, so the FDC3300 can be easily upgraded in the 

field using the local RS-232 port.  We make all firmware upgrades for our products available to our 

customers free of charge.  

 

Theory of Operation

Overview

The diagram below illustrates the FDC3300 architecture.  Single or dual power supply operation is 

supported with any combination of AC or DC input voltages.  The presence of proper voltage at the 

output of each of the two internal DC-DC converters is detected and monitored by the alarm logic 

and CPU.  The outputs of these two power supplies are diode “OR’d” to power the FDC3300.

Single or dual signal inputs are detected and monitored by the alarm logic and CPU.  In addition, 

single or dual TTL level disable inputs are monitored to allow switching based on the alarm output 

from the upstream signal source.  This external alarm signal can be connected to rear-panel BNC 

connectors labeled “DISABLE IN”.  These disable inputs are pulled up with 10k ohm resistors so 

that they may be connected to an open-collector output signal.  Based on the status of the signal input 

level detection and the disable inputs, the alarm logic and CPU control the signal input switch.  You 

can configure a variety of automatic switching strategies and also manually force the selection of 

either input.

The output signal from the switch is buffered and drives ten broadband output amplifiers.  Output 

signal level detectors for each of the ten channels are monitored by the alarm logic and CPU so that 

output amplifier failure or interconnect cable short circuits may be observed.

All status information is reported via the front-panel LEDs and the serial I/O port or optional Ethernet 

interface.  A summary open-collector alarm output is provided. 

Summary of Contents for FDC3300









































Reviews: