EnergoInfra Industry EIR3000, EIR4500 and
EIR6000, 400V3N~, are intended for permanent
installation by an authorized electrician and in
accordance with existing national regulations. The
appliance must be preceded by an all-pole switch,
min. 3mm contact gap. Appliance and protection
class: Class I - IP44.
1
. The EIR Industry can be mounted to the ceiling or
on the wall, horizontally, where the lowest installa-
tion height is 2.3m from the floor level. Respect and
follow the minimum distances to the surrounding
surfaces, according to fig.1.
NOTE! Do not cover the heater or direct it towards
combustible items. Fixed heater must not be mount-
ed in front of a socket outlet.
2
. The supplied ceiling/wall brackets should be
mounted with a C/C distance, see fig.2 and table.
The brackets can be angled in different positions,
when wall mounted. There are two mounting holes
per ceiling bracket, where “D” is the distance be-
tween the holes, fig.3. The fixing brackets “FB”, on
top of the heater, is to be hung up and fixed to the
ceiling/wall brackets.
3
. Alternative suspension kits are available to ease
installation using wall wire mount or chains.
4
. On top of the heater there are two cable grom-
mets “CG”, fig.2, allowing multiple connections.
Connection according to fig.4a, to a 16mm² terminal
block. Using this connection, one heating element
at a time can be connected (for three output steps).
Protect the supply cable, if it comes in contact with
hot parts!
Note! The heater may also be connected to 230V1~
by some internal rewiring. Visit our web site to
download the wiring instruction:
www.energotech.com/media/31441/230V.pdf
5
. When starting-up the heater for the first time or
after a long period of disuse, smoke or odor may
result from grease, dust or dirt that has collected on
the element. This is normal and disappears after a
short period of time.
6
. Like in all electrical heating appliances, clicks
can occur during expansion and contraction of the
material, due to movement when the temperature
changes.
7
. The heater may undergo a color variation fol
-
lowing being energized for the first time and during
its life span. The extent is relevant to the operating
environment and is normal behavior.
Aerosols, paint, solvents, dust and filth etc... may
adhere to the heater and can potentially cause
discoloration. The performance of the heater is
unaffected by discoloration. As a precaution, always
switch off the heater while painting and drying!
8
. When cleaning the heater, make sure that the
heater is switched off. Let the heater cool down.
Use a soft cloth to clean the body of the heater. For
cleaning the reflector, use a clean soft brush.
9
. If refit is needed, the heating elements can be
replaced in site without having to take down the
heater. Unscrew lid and wires. Pull out the part in
question and replace with a new one.
10
. Information about energy consumption
In combination with an Ecodesign-compliant
thermostat, the product data complies with the EU
regulations on the Ecodesign Directive (2009/125/
EC) for energy-related products (ErP).
11
. Safety
• When the installation is protected by an RCD, a
300mA residual current device has to be used.
• Warning - Hot surface! Do not touch the heater
when in use!
•
Do not cover the heater! Risk of fire!
• This appliance shall not be used by children less
than 8 years or persons with reduced physical,
sensorial or mental disability or lack of experi-
ence and knowledge, unless they are supervised
or were instructed how to use the appliance in a
safe way, and understand the hazards involved.
Children shall not play with the appliance. Clean-
ing and user maintenance shall not be made by
children without supervision.
ENGLISH
ErP
✔
