background image

21

10.6.2  Blade Replacement - Fixed Blade

Replace the fixed blade as described in the following 

steps. Refer to Figure 16, items 3, 4 and 5.
1. Be sure that the cutter piston is fully retracted. If not, 

start the cutter and cycle the piston until it is fully 

retracted.

 

NOTICE

If battery is fully discharged and the piston is 

extended, loosen the piston release screw to retract the 

piston, as described in Section 8.3.

2. Remove battery from cutter to prevent accidental 

motor startup during the following steps.

3. Place the cutter horizontally on a stable work surface.
4. Remove the fixed blade screw.
5. Remove the safety guard. 
6. Remove the worn fixed blade and replace it with the 

new fixed blade. 

7. Secure the safety guard and new fixed blade using 

the new fixed blade screw included with the new fixed 

blade. Apply Loctite 243 thread sealant (or equivalent) 

to threads. Torque to 18 ft-lb [25 Nm].

8. Test cutter for proper operation before placing it back 

into service.

10.6.3  Blade Replacement - Moving Blade

Replace the moving blade as described in the following 

steps. Refer to Figure 16, items 1 and 2.
1. Be sure that the cutter piston is fully retracted. If not, 

start the cutter and cycle the piston until it is fully 

retracted. If battery is fully discharged, loosen the 

piston release screw as described in Section 8.3.

2. Remove battery from cutter to prevent accidental 

motor startup during the following steps.

3. Place the cutter horizontally on a stable work surface.
4. Remove the moving blade screw.
5. Remove the worn moving blade and replace it with 

the new moving blade.

6. Secure the new moving blade using the new moving 

blade screw included with the new moving blade. 

Apply Loctite 243 thread sealant (or equivalent) to 

threads. Torque to 91.2 in-lb [10.3 Nm].

7. Test cutter for proper operation before placing it back 

into service.

Figure 16, Fixed and Moving Blade Replacement

2

5

1

4

3

Key:

1. Moving Blade

2. Moving Blade Screw

3. Fixed Blade Screw

4. Safety Guard

5. Fixed Blade

Summary of Contents for EBC20B





























Reviews: