background image

7

017-220-J0    Rev C

1.  Safety

SAVE THESE INSTRUCTIONS: 

This manual contains important safety instructions that must 

be followed during the installation, servicing, and maintenance of the product. Keep it in a safe place. Review the 
drawings and illustrations contained in this manual before proceeding. If there are any questions regarding the safe 
installation or operation of this product, contact Alpha Technologies or the nearest Alpha representative. Save this 
document for future reference.

1.1  Safety Symbols

To reduce the risk of injury or death, and to ensure the continued safe operation of this product, the following sym-
bols have been placed throughout this manual. Where these symbols appear, use extra care and attention.
The use of ATTENTION indicates specific regulatory/code requirements that may affect the placement of equipment 
and /or installation procedures.

WARNING!

WARNING presents safety information to PREVENT INJURY OR DEATH to personnel. 
Warnings are indicated by a shock hazard icon, the word WARNING, and a rule beneath 
which the information appears.

CAUTION!

CAUTION indicates safety information intended to PREVENT DAMAGE to material or 
equipment. Cautions are designated with a yellow warning triangle, the word CAUTION, 
and a rule beneath which the information appears.

NOTE:

A NOTE provides additional information to help complete a specific task or procedure. 
Notes are designated with a check mark, the word NOTE, and a rule beneath which the 
information appears.

HOT!

The use of HOT presents safety information to PREVENT BURNS to the technician or 
user.

HOT!

The use of HOT symbol (ISO 8005) on the product indicates a potential burn hazard to 
the technician or to the user.

Summary of Contents for Alpha Micro 100

























































































Reviews: