EnfaSafe 360 ONE FOR ALL Instruction Manual Download

Page: 12 / 15

5.1. INSTALLED IN THE CAR WITH BELT

5.1.2.2.

Group II III (15-36kg)

NOTE:

When you use this safety car seat in

Group II III, please remove the 5-point harness,

sleeping pads and the triangle pads (refer to 4.7.).

Place the child seat forward facing on

the vehicle seat (in the direction of travel).

Press the adjust button of support leg, adjust the

support leg upwards to the shortest, make it hang.

Ensure that the support leg shows red indicator.

First pull out the belt from the belt ALR. Diagonal

belt through the same side of Guidance , lap belt

through the same side of Guidance , then pull the

diagonal belt and lap belt together through another

side of Guidance .

NOTE:

Keep the diagonal belt at the position

of shoulder between the outside of the neck

and shoulder (middle of point A and B )

(see picture a).

Lock the tip of the buckle into the vehicle

seat buckle with a CLICK noise. Follow the

direction of arrow to tighten belt, and put

redundant belt into cloth cover. Check the child

safety car seat to make sure it is securely

attached.

5.1. INSTALLED IN THE CAR WITH BELT

5.1.2.

Installed in forward facing position with belt

5.1.2.1.

Group 1 (9-18kg)

Place the child seat forward facing on the vehicle

seat (in the direction of travel).

Pull out the support leg, adjust it to the

maximum angle.

Press the adjust button of support leg, adjust the

length of the support leg so that it is in full contact

with the ground of the vehicle (display window

turns green).

Pull the diagonal belt section through belt

guidance .Place the lap belt section in the

belt guidance .

Pull out safety belt from the back to the side, lap

belt section respectively from the belt guidance

of the base. One side of the diagonal belt through

the backrest and the belt guidance ,another side

along the upper inside.

Using your knee to press down on the child seat,

tighten the vehicle seat belt as follows:

Pull on the lower part of the diagonal seat belt

section near the vehicle seat buckle to tighten the

lap belt section.

CAUTION!

The diagonal seat belt section must run

diagonally backward. You can adjust the course of

the belt with your vehicle's adjustable belt deflector

on both sides.

Ensure the lap

belt is as close as

possible to lower.

Ensure the lap

belt is on the

pelvis, not on the

abdomen.

CLICK

Summary of Contents for 360 ONE FOR ALL
















Search results

Summary of Contents for 360 ONE FOR ALL

Reviews:

Related manuals for 360 ONE FOR ALL

Brands by name

Popular brands

EnfaSafe 360 ONE FOR ALL, Instruction Manual

Search results

Summary of Contents for 360 ONE FOR ALL

Reviews:

Related manuals for 360 ONE FOR ALL

Brands by name

Popular brands