background image

25

26

CAUTION!

 The diagonal seat belt section must

run diagonally backward. You can adjust the

course of the belt with your vehicle’s adjustable

belt deflector on both sides.

5.2. INSTALLED IN THE CAR WITH ISOFIX CONNECTOR

5.2.3.

 Installed in forward facing position with ISOFIX

connector and belt; Group II III (15-36kg).

NOTE:

 When you use this safety car seat in

Group II III please remove the 5-point harness,

sleeping pads and the triangle pads (refer to 4.7.)

Place the child seat forward facing on the vehicle

seat (in the direction of travel).

Put the ISOFIX insert guide into the two ISOFIX

attachment points of your vehicle.

If you don’t have the ISOFIX insert guide, please

ignore this step.

NOTE:

 The ISOFIX attachment points are located

between the surface and the backrest of the vehicle

seat.

Press the ISOFIX button to pull out the two locking

arms from the base bottom. Pull the locking arm to

and fro until you hear an audible CLICK which

indicates they are fully engaged. Both sides of the

locking arms’ button turn green.

Press the adjust button of support leg, adjust the

support leg upwards to the shortest, allowing it

to hang.

Ensure that the support leg shows red indicator.

First pull out the belt from the belt ALR. Diagonal

belt through the same side of Guidance    , lap belt

through the same side of Guidance

    

, then pull the

diagonal belt and lap belt together through another

side of Guidance    .

NOTE:

 Keep the diagonal belt at the position of

shoulder between the outside of the neck and

shoulder (middle of point  A  and  B )

(see p25 picture a)

Lock the tip of the buckle into the vehicle seat

buckle when hear an audible CLICK. Follow the

direction of arrow to tighten belt, and put

redundant belt into cloth cover. Check the child

safety car seat to make sure it is securely

attached.

6. CARE AND MAINTENANCE

Periodically inspect your child seat for worn or

damaged parts. If damaged parts are found,

replace the child seat. Keep the child seat clean.

Do not lubricate any parts of the child seat.

To prolong the life of your car seat, keep it

clean and do not leave it in direct sunlight for

extended periods of time.

Removable fabric covers and trims may be cleaned

using warm water with a household soap or a mild

detergent. Allow it to dry fully, preferably away from

direct sunlight.

CLEANING THE BUCKLE:

Food, drink, or other debris may collect inside the

harness buckle which can affect proper functioning.

Wash in warm water until clean. Be sure you can

hear an audible CLICK to make sure the buckle is

working properly.

Ensure the lap

belt is as close as

possible to lower.

Ensure the lap

belt is on the

pelvis, not on the

abdomen.      

a

A

B

Summary of Contents for 360 ONE FOR ALL
















Reviews: