Copyright ©2012 Enforcement Technology Group, Inc. (ETGI). All Rights Reserved. Information subject to change without notice. Bluetooth
®
is a registered trademark of Bluetooth SIG, Inc.
PRE
‐
OPERATIONS
SET
‐
UP
&
COMPONENT
CONCEALMENT
(CONTINUED):
Connecting,
Concealing,
and
Positioning
the
Low
Profile
Microphone:
1. Locate
the
“
Low
Profile
Microphone
” (provided).
2. Attach
the
“
Low
Profile
Microphone
” to
the
Field
Operator’s
shirt
collar/lapel
or
other
area
near
the
mouth
of
the
Field
Operator
by
using
the
provided
clip.
NOTE:
The
"Low
Profile
Microphone"
should
be
attached
in
a
concealed
manner
to
help
prevent
it
from
being
identified
by
a
subject.
3.
Conceal
the
“
Low
Profile
Microphone
” cable
by
running
it
under
the
shirt
of
the
Field
Operator.
4.
Insert
the
pin
end
of
the
“
Low
Profile
Microphone
” into
the
“
MIC
” port
located
on
the
side
of
the
Concealed
Communicator
™
Base
Unit.
Connecting,
Concealing,
and
Positioning
the
Neck
Loop
Transmitter:
1. Locate
the
“
Neck
Loop
Transmitter
” (provided).
2. Place
the
“
Neck
Loop
Transmitter
” around
the
neck
of
the
Field
Operator.
NOTE:
The
"Neck
Loop
Transmitter"
should
be
attached
in
a
concealed
manner
to
help
prevent
it
from
being
identified
by
a
subject.
3. Conceal
the
“
Neck
Loop
Transmitter
” cable
by
running
it
under
the
shirt
of
the
operator.
4.
Insert
the
pin
end
of
the
“
Neck
Loop
Transmitter
” into
the
“
LOOP
” port
located
on
the
side
of
the
Concealed
Communicator
™
Base
Unit.
Connecting,
Concealing,
and
Positioning
the
Tone
Generator
Button:
1.
Locate
the
"
Tone
Generator
Button
"
(optional).
2.
Conceal
the
"
Tone
Generator
Button
"
cable
and
place
the
button
in
an
area
that
is
readily
accessible
by
the
Field
Operator
such
as
in
their
pocket.
3.
Insert
the
pin
end
of
the
"
Tone
Generator
Button
"
into
the
"
BUTTON
"
port
located
on
the
side
of
the
Concealed
Communicator
™
Base
Unit.
Concealing
the
Bluetooth
®
Enabled
Cell
Phone
(BECP)
and
the
Concealed
Communicator
™
Base
Unit:
1.
After
the
"
Low
Profile
Microphone
,"
"
Neck
Loop
Transmitter
,"
and
"
Tone
Generator
Button
"
(optional)
have
been
connected
and
concealed;
conceal
the
Concealed
Communicator
™
Base
Unit
and
BECP
that
the
device
is
paired
to
in
the
Field
Operator's
pocket.
"Earpiece
Magnet"
Insertion
Procedures
&
Warnings:
1.
The
Field
Operator
should
insert
either
the
"
Small
Earpiece
Magnets
"
OR
"
Large
Earpiece
Magnets
"
into
their
ear
canals
in
accordance
with
the
"
EARPIECE
MAGNET
INSERTION
PROCEDURES
&
WARNINGS
"
section
of
this
manual.
8
