Electromechanical Push Bars
Installation (Continued)
8.
Install the strike assembly as shown in Fig. 5 on pg. 3. Ensure a
3
/
16
" (4~5 mm) gap between the strike assembly and end cap
(see Fig. 7). Use included spacers as needed.
9.
Ensure the push bar and strike are operating smoothly and the
locking spindle teeth fully engage the strike before tightening the
two main strike assembly screws. Drill and install the middle
screw as the final step (see Fig. 5 on pg. 3).
Wiring Diagram
When connecting solenoid-actuated models to an access control system or a control device, note
that the latch retraction duration is controlled by the connected N.O. switch.
Troubleshooting
Bar does not unlock when
triggered (models with solenoid)
•
Check the input voltage (12~24 VAC/VDC)
•
Check that the trigger switch is operating properly
Buzzing sound when activated
(models with solenoid)
•
This may sometimes result when using AC voltage. Change to DC
if it persists
Device does not unlock
•
Check back pressure on latch and adjust
Power Supply
12/24
VAC/VDC
+
–
Access control
PB
Lock status
indicator
Relay rating
5A@125VAC
PB
N.O.
COM
N.C.
–
+
Lock status output
12~24 VAC/VDC
N.O.
COM
–
+
Access
Control
Keypad /
Proximity
Reader
Brown N.O.
Green COM
White N.C.
Connect lock status output according to status indicator directions
SD-961x-36GSQ Series Solenoid-Actuated Push Bars
Connection to Access Control Device
SD-961x-36GQ Series Manual Push Bars
Connection to Lock Status Indicator
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
PITGW1
MI_SD-961x-36GxQ_211125.docx
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale
to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to
SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper
or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other
than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair
only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind
to the purchaser or anyone else.
NOTICE:
The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2022
SECO-LARM U.S.A., Inc. All rights reserved.
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information, go to
www.P65Warnings.ca.gov
.
IMPORTANT:
Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies with all national, state,
and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
IMPORTANT:
The height at which the push bar is mounted may be subject to local regulations. It is the responsibility of the installer and/or end-user customer to
ensure the push bar meets all local regulations regarding the use of push bars for access security, including height, suitability for doors accessed by disabled persons,
and suitability for fire doors (the push bar is not fire-rated).
WARNING:
The push bar is not weatherproof. Do not mount on exterior surface or where exposed to rain.
Fig. 7
3
/
16
" (4~5 mm)
Strike
End cap
