background image

ENFORCER Outdoor Stand-Alone Keypads 

 

10

 

                                                        

SECO-LARM U.S.A., Inc.

 

 

 

 

4. Exit Programming Mode by pressing        .

 

 

Program a new Master Code immediately. 

 

Take note of the keypad status LEDs— 

o

 

Right LED Solid Green: 

Standby Mode 

o

 

Right LED Solid Orange:

 Programming Mode 

o

 

Left LED Solid Green / Right LED Flashing Orange:

 Awaiting code/card entry 

 

If you are unsure of which mode the keypad is in, press       until the right LED is green.  The keypad is now 
in the Standby Mode.  Enter the master code twice to return to Programming Mode. 

Enter: 

1.

 

Codes are programmed to have 2~6 digits in length.  All codes must be the same length. 

2.

 

Before inputting any of the following, enter Programming Mode by entering the  
Master Code twice.  

The default Master Code is 1234.   

To enter Programming Mode, enter

  

3.

 

To exit Programming Mode, press the        key.

 

4.

 

The keypad will exit Programming Mode if no keys are pressed for 30 seconds.

 

Programming Instructions 

Programming Tips 

First Time Keypad Use

 

Take these steps the first time the keypad is programmed. 

1. Enter Programming Mode by entering the Master Code twice.  (Default Master Code is 

1234

). 

     

2. Enter             
3. Enter the new Master Code twice.  The Master Code may not be the same as a user code. 

C.

 

Program the Master Code 

 

Example:

 If the desired new Master Code is 

4321

, enter: 

4  3  2  1  4  3  2  1 

4. Exit Programming Mode by pressing        . 

A.

 

Enter Programming Mode

 

 

(Default Master Code is 

1234

). 

*SK-2323-SPQ and SK-1323-SPQ only. 

B.

 

Program Code Length

 

 

1. Enter Programming Mode by entering the Master Code twice.  (Default Master Code is 

1234

). 

     

2. Enter             

 

3. Enter the desired code length.  This must be a number from 2~6. 

WARNING: 

After a new code length is programmed, all user codes will be deleted and master code will 

be reset. 
     

2  3 

1  2 

3  4 

2  3 

4  1  2 

3  4 

Note:

 The Master Code will reset depending on the programmed code length.  These will be the new  

Master Codes after the code length is reset: 

 

Code Length 

New Master Code 

2 digits 

12 

3 digits 

123 

4 digits 

1234 

 

Code Length 

New Master Code 

5 digits 

12345 

6 digits 

123456 

 

0  4 

Summary of Contents for SK-1323-SDQ
















Reviews: