background image

Page 1

INSTALLATION, OPERATION

AND MAINTENANCE MANUAL

INDEX

PAGE

INTRODUCTION ............................................................................................................. 2
WARRANTY ................................................................................................................... 2
RECEIVING THE UNIT ................................................................................................... 3

INSTALLATION

CODES ........................................................................................................................... 3
CLEARANCES ................................................................................................................ 3
LOCATION...................................................................................................................... 4
SUSPENSION MOUNTING ............................................................................................. 4
ASSEMBLY OF TWO - PIECE UNITS............................................................................. 4
COOLING COILS ............................................................................................................ 5
DRAIN TRAPS ................................................................................................................ 5
VENTING ........................................................................................................................ 6

A) SIDE WALL INDIVIDUAL VENT ............................................................................ 6
B) VERTICAL INDIVIDUAL VENT.............................................................................. 8
C) OPTIONAL VERTICAL VENT TERMINAL ............................................................. 9

INSULATION OF SINGLE WALL VENT PIPE.................................................................. 9
COMBUSTION AIR ....................................................................................................... 10
GAS INSTALLATION .................................................................................................... 10
DUCTWORK................................................................................................................. 11
ELECTRICAL INSTALLATION ...................................................................................... 11
COMBUSTION AIR PROVING SWITCH........................................................................ 11
START-UP CHECK LIST............................................................................................... 11

OPERATION

OPERATIONAL CHECK ............................................................................................... 12
OPERATING INSTRUCTIONS ...................................................................................... 13

MAINTENANCE

SET SCREWS .............................................................................................................. 14
LUBRICATION .............................................................................................................. 14
PULLEYS AND BELTS ................................................................................................. 14
FILTERS ....................................................................................................................... 14
CONTROLS .................................................................................................................. 14
FURNACE INSPECTION AND CLEANING .................................................................... 14
SUMMER OPERATION ................................................................................................ 15

Summary of Contents for DH-FP-PV series

















Reviews: