background image

− 7 −

134

TEMPERATURE SETTING

Temperature Control

When using the refrigerator, please turn the dial in order
to adjust the Temperature.

Inside Temperature varies, depending on the outside
Ambient Temperature.

To adjust the Dial :       when outside Temp 30

Dial Location

Approx. Temperature

OFF

shut OFF

1

Approx.   8 

3

Approx.  -2 

5

Approx.  -8 

※ If the Outside Temperature decreases,

the inside refrigerator Temperature may be affected.

When storing Food and Beverages

1) Please do not overload the refrigerator. Try to have some space between the goods when 

loading into the refrigerator. If overloading occurs some items may not cool efficiently.

2) Please do not store warm or heated foods or beverages.

(Make sure to cool the foods and beverages before storing into the refrigerator)

3) Watery goods or strong smell food store should be wrapped. 

4) The refrigerator has been thoroughly cleaned prior shipment from the factory.

However, it is advisable to clean the interior once again before use.
Clean the interior with a damp cloth in warm water, and wipe with a dry cloth.

5) The temperature control is located on the upper left side in the refrigerator compartment.

The space between the bottom of the controller and the bottom of the tray is less than 134mm.
Please note so the controller is not damaged.

6) Please wipe the bottom of tray with a soft, dry cloth regularly.

If the door does not open because of ice between tray and cabinet, you may need to power off 
the refrigerator to allow the ice to thaw.

1

2

3

4

5

0

OFF

COOL

REF.

TEMPERATURE

CONTROL

Summary of Contents for SB30G














Reviews: