enphase Enphase Envoy-S Metered Installation And Operation Manual Download

Page: 3 / 49

Envoy-S Installation and Operation



2016 Enphase Energy Inc.

141-00031 Rev 01

Table of Contents

SAFETY ..................................................................................................................................... 5

Read this First .................................................................................................................................. 5

Safety Instructions ........................................................................................................................... 5

The Enphase Envoy-S ............................................................................................................... 6

How the Enphase Microinverter System Works .............................................................................. 6

Installation Planning and Preparation ......................................................................................... 7

Pre-installation Checks .................................................................................................................... 7

Select the Envoy-S Type to Install ............................................................................................... 7

Download the Installer Toolkit App .............................................................................................. 8

Box Contents ............................................................................................................................... 8

Plan the Power Connection ......................................................................................................... 8

Use a Phase Coupler for a Three-Phase Site ............................................................................. 8

Plan the Internet Connection ....................................................................................................... 9

Metering Considerations .............................................................................................................. 9

Required Items............................................................................................................................. 9

Optional Items .............................................................................................................................. 9

System Metering Options .......................................................................................................... 10

Create the Map and Install the PV Modules and Microinverters ............................................... 10

Installation Sequence .................................................................................................................... 11

Installing the Envoy-S ............................................................................................................... 12

1. Choose a Location for the Envoy-S ........................................................................................... 13

2. Provide a Power Connection ..................................................................................................... 13

Provide Power for the Envoy-S Standard (ENV-S-WB-230-F, -G, and -I) ................................ 13

Provide Power for the Envoy-S Metered (ENV-S-WM1-230) .................................................... 15

3. Install CTs for Metering (Model ENV-S-WM1-230 only) ............................................................ 16

Install the CT for Production Metering ....................................................................................... 16

Install the CT for Consumption Metering (optional) ................................................................... 17

Extend Consumption CT Leads, If Needed ............................................................................... 17

4. Energise the Envoy-S ................................................................................................................ 17

5. Detect the Microinverters ........................................................................................................... 18

Method A: Provision Microinverters with Installer Toolkit .......................................................... 18

Method B: Discover Microinverters with Installer Toolkit ........................................................... 18

Method C: Discover Microinverters with the Envoy-S ............................................................... 18

With All Methods ........................................................................................................................ 18

6. Verify System Configuration ...................................................................................................... 19

7. Connect to Enlighten ................................................................................................................. 19

Method A: Integrated Wi-Fi ........................................................................................................ 19

Method B: Enphase Mobile Connect Modem ............................................................................ 20

Method C: Ethernet Cable ......................................................................................................... 20

Method D: Power Line Communication Bridges ........................................................................ 21

If the Internet Connection Fails .................................................................................................. 21

8. Send System Summary Report ................................................................................................. 21

Activate Monitoring ................................................................................................................... 22

Method A: If the Envoy-S is Associated with a System in Installer Toolkit ................................ 22

Method B: If the Envoy-S is NOT associated with a System in Installer Toolkit ....................... 22

View System Performance in Enlighten .................................................................................... 22

Envoy-S Operation ................................................................................................................... 23

Envoy-S Displays and Controls ..................................................................................................... 23

Envoy-S LED States ...................................................................................................................... 23

LED Behaviour at Initial Start Up ................................................................................................... 24

Initial Communications Check ................................................................................................... 24

More about Microinverter Communications States.................................................................... 24

Initiate a New Scan for Microinverters ........................................................................................... 24

Connecting to Envoy-S ............................................................................................................. 25

Connect Using the Installer Toolkit App ........................................................................................ 25

Summary of Contents for Enphase Envoy-S Metered


















































Search results

Summary of Contents for Enphase Envoy-S Metered

Reviews:

Related manuals for Enphase Envoy-S Metered

Brands by name

Popular brands

enphase Enphase Envoy-S Metered, Installation And Operation Manual

Search results

Summary of Contents for Enphase Envoy-S Metered

Reviews:

Related manuals for Enphase Envoy-S Metered

Brands by name

Popular brands