Enphase Customer Support:
http://enphase.com/global/contact
-
F I E L D W I R E A B L E Q C O N N E C T O R S - T H R E E - P H A S E
Safety Symbols
+
DANGER
: This indicates a hazardous situation, which if
not avoided, will result in death or serious injury.
*
WARNING
: This indicates a situation where failure to
follow instructions may be a safety hazard or cause
equipment malfunction. Use extreme caution and follow
instructions carefully.
;
WARNING
: Risk of burn. Failure to follow instructions may
result in burn injury.
✓
NOTE
: This indicates information particularly important
for optimal system operation.
SAFETY
IMPORTANT SAFETY INSTRUCTIONS.
SAVE THIS INFORMATION.
Follow all safety and assembly instructions when installing En-
phase Field Wireable Q Connectors.
Safety Instructions
+
DANGER
: Risk of electric shock. Do not use Enphase
equipment in a manner not specified by the manufacturer.
Doing so may cause death or injury to persons, or dam-
age to equipment.
+
DANGER
: Risk of electric shock. Be aware that installation
of this equipment includes risk of electric shock. Do not
use without first removing AC power from the Enphase
System. Disconnect the power coming from the photovol-
taics before servicing or installing.
+
DANGER
: Risk of electric shock. Risk of fire. Before mak
-
ing any connections verify that the circuit breakers are in
the off position. Double check all wiring before applying
power.
+
DANGER
: Risk of electric shock. Risk of fire. Only use
electrical system components approved for wet locations,
including but not limited to conduit fittings.
+
DANGER
: Risk of electric shock. Risk of fire. Only qualified
personnel should install, troubleshoot, or replace the
Enphase Field Wireable Q Connector.
+
DANGER
: Risk of electric shock. Improper use of the Field
Wireable Q Connector or its components may result in a
shock, fire or explosion. To reduce these risks, disconnect
all wiring before attempting any maintenance.
+
DANGER
: Risk of electric shock. Risk of fire. Ensure that all
AC and DC wiring is correct and that none of the AC wires
are pinched, shorted, or damaged.
+
DANGER
: Risk of electric shock. Risk of fire. Do not
attempt to repair or alter the Enphase Field Wireable Q
Connector.
+
DANGER
: Risk of electric shock. Risk of fire. Make sure the
conductors are not damaged. If the exposed wires are
damaged, the system may not function properly.
*
WARNING
: Risk of equipment damage. Enphase male and
female connectors must only be mated with the matching
male/female connector.
*
WARNING
: Risk of equipment damage. This product is
intended for operation with a maximum operating temper-
ature of 110ºC.
*
WARNING
: When installing the cabling, secure any loose
cable to minimize tripping hazard.
*
WARNING
: Before installing or using the Enphase Field
Wireable Q Connector, read all instructions and cautionary
markings in the technical description, on the Enphase
System, and on the photovoltaic (PV) equipment.
*
WARNING
: Never plug in or disconnect the connectors
under load. The connectors are not suitable for interrupt-
ing the current.
*
WARNING
: Without earthing connection.
✓
NOTE
: Using unapproved attachments or accessories
may result in damage or injury.
✓
NOTE
: When looping the Enphase Q Cable, do not form
loops smaller than 12 cm in diameter.
✓
NOTE
: Perform all electrical installations in accordance
with all applicable local electrical codes.
✓
NOTE
: To ensure optimal reliability and to meet warranty
requirements, install the Enphase Field Wireable Q Con-
nectors according to the instructions in this guide.
✓
NOTE
: Protection against lightning and resulting voltage
surge must be in accordance with local standards.
✓
NOTE
: The connector is considered to be in compliance
only when assembled in the manner specified by these
assembly instructions.
✓
NOTE
: For flexible wires, we recommend using ferrules
acc. to DIN 46228 that are crimped with jointing clamp.
✓
NOTE
: Cable used with Enphase Field Wireable Q Connec-
tors must meet the following requirements:
• Min/max outer insulation diameter (including the
clear second insulator): 8mm / 21mm
• Wire size: 2.5mm2 to 6mm2
DISCONNECT (if needed)
To disconnect Enphase three-phase Field Wireable Q Connectors,
release the two connectors by pressing down the snap with a screw-
driver. You can then separate the connectors.
*
WARNING: Never plug in or disconnect the connectors under
load. The connectors are not suitable for interrupting the current.
Enphase Article Number Enphase Product SKU Type Designation
150-00094
Q-CONN-3P-10F
PRC 5-FC-FS6...
150-00093
Q-CONN-3P-10M
PRC 5-FC-MS6...
