background image

Ensitech Pty Ltd

www.tigbrush.com

19 

ON/OFF SWITCH ILLUMINATED, CIRCUIT BREAKER 
PRESSED IN & UNIT NOT OPERATING

UNIT OPERATING IN CLEAN MODE ONLY

•  Ensure the TIG Brush circuit breaker is reset (it should 

be pressed in – see back of unit). 

•  Ensure the cables are securely plugged into the front of 

the TIG Brush. 

•  Ensure the clamp is gripping the work securely. 

Sometimes the clamp position may need adjusting to 
make a good contact. If dirt or debris has built up on the 
clamp, clean it as this may prevent a good contact  
being made. 

•  Ensure the brush or marking head is wet with fluid. 
•  Ensure that the work is conductive. If the metal has a 

plastic film or a thick layer of oxide, the current cannot 
flow through the work. A mechanical or chemical 
method may need to be used to remove any insulating 
film before the TIG Brush can be used. 

•  Examine all cables for damage and ensure all the cables 

are properly connected.

•  Ensure the brush or marking head adapter is securely 

screwed into the wand. NOTE: Be careful when 
checking, as a loose connection may be extremely hot.

•  Check screw threads on the handle, wand, brush or 

marking head adapter for dirt and contamination in the 
screw threads and clean if required. 

•  The unit is faulty. Return the unit to your local Ensitech 

supplier for servicing.

S8 TROUBLESHOOTING

8.3

8.4

Contact your TIG Brush distributor or visit the website for 
more help 

www.tigbrush.com

Summary of Contents for TIG BRUSH TBE-160CM





















Reviews: