background image

 

Installation instruction  

of the flat solar collectors models ES1V2.0, ES1V2.65,  

ES2V/2.0 AL, ES2V/2.65 

 integrated in the slate roof.   

 

5. Maintenance and Service 

 

4.

 

During the maintenance and other kind of work a collector must be placed firmly 
to exclude the danger of tripping over and falling down, 

5.

 

It is not allowed to perform any repair and maintenance work under a lifted 
collector which has not been protected against casual falling down,   

6.

 

Repair and maintenance work should be done by means of suitable tools and the 
servicing personnel should wear protective gloves and shoes,  

7.

 

Before the commencement of maintenance work it is necessary to wait till the 
temperature of a collector lowers to such an extent that a risk of getting scalded 
by hot elements is excluded,  

8.

 

Overhaul of the solar system needs to be done in accordance with warranty 
recommendations for particular elements of the system.    

 

In order to guarantee failure-free operation of the whole system it is 

 

recommended to carry out the following maintenance work at least once a year:  

1.

 

Frost protection – check the solar fluid resistance to frost by means of a control 
device (refractometer). In case of a significant fall in frost resistance of the solar 
fluid it should be replaced and the system must be deaerated once again.   

2.

 

System pressure – working pressure in the solar system needs to be checked.  
After the start-up period no drop of pressure is permissible.  

3.

 

Expansion vessel – input pressure of the expansion vessel should be checked.  
To this end,  disconnect the vessel from the system and measure the pressure. The 
input pressure should be 2,5 bars.   

 

 

The control and protection system should also be inspected along with the  

 

 

structure for supporting and fixing a collector on the roof.  

 
 

 

In order to guarantee the proper operation of the whole system, every time we 

 

 

recommend you to enter into a contract for maintenance work with a specialist 

 

 

installation firm.   

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

  

 

Energetyka  Solarna  Ensol  Sp.  z 

o.o. 

47-400 Racibórz,  ul. Piaskowa 11 

Tel/fax: 0048 32 415 9665 

Summary of Contents for ES1V2.0





















Reviews: