background image

MN-28646 • Rev 4 • 03/18 • EC Series Fluid Combination Blanket/Fluid Warmer

4

General Information

This warming cabinet is designed to safely warm and store 

blankets and either irrigation fl uids or injection fl uids.
The dual-chambered warming cabinet is constructed with 

stainless steel exterior casing and door with handle and hinges 

designed to withstand heavy usage. A door with window 

allows observation of inventory with the door closed. The 

cabinet is warmed using low-heat-density electrothermal 

cable array. The electrothermal cable is positioned in the fl oor 

and two sides of the warming cabinet, providing even heating 

of the interior chamber.
Each chamber's temperature is regulated by a separate 

electronic control consisting of a 4 digit L.E.D. display, 

ON/OFF button, INCREASE and DECREASE buttons, 

integrated lock-out control feature and a series of prompt 

sequence indicators.
Each control can easily be set to operate in Fahrenheit or 

Celsius. Aft er a power failure, the cabinet will remember its 

programming and begin to operate as before. The ON/OFF 

indicator will blink to indicate a failure occurred; pressing the 

ON/OFF button once will eliminate this blinking. A thermal 

shut-off  system, separate from the electronic controls, is 

included as an additional safety feature.
The control will display temperature in whole degrees.

Blanket warming chamber:
The design and operational characteristics of the chamber 

eliminate the need for a heat circulating fan.
The controller has an adjustable temperature range of 

37°C to 93°C (98°F to 200°F).
The timer feature allows the user to program the controller 

to automatically switch on and switch off  once during a 

24-hour period at selected times. This enables the chamber to 

be turned off  automatically at night to save energy, but turned 

on again in the early morning to ensure warm blankets are 

available. 

Fluid warming chamber:
The warming appliance can be programmed to warm 

either irrigation fl uids (IRR) or injection fl uids (INJ), with 

separate temperature ranges provided depending on the 

choice selected. 

•  IRR temperature range: 37°C to 66°C (98°F to 150°F), 
•  INJ temperature range: 37°C to 40°C (98°F to 104°F). 

A fan located inside the chamber mixes the air to prevent 

temperature stratifi cation and to ensure an accurate 

chamber temperature for each mode. 

•  0/-1.12°C (+0/-2ºF) for set points of 

37°C to 40°C (98°F to 104°F).

•  0/-1.67°C (+0/-3ºF) for set points of 

43°C to 66°C (110°F to 150°F)

An alarm will sound if temperatures exceed 6°C (10°F) over 

the set-point temperature, and an overtemp indicator will 

blink indicating an over-temperature condition. 

The blanket warming chamber includes a white, epoxy-

coated blanket support assembly and two (2) shelves. The 

fl uid warming chamber is equipped with one (1) white, 

epoxy-coated shelf to accommodate most commonly used 

surgical fl uids packaged in bags or bottles. The basket has a 

capacity of 

18 1-liter bottles or 28 1-liter bags.

 The cabinet is 

furnished with four (4) leveling feet.

EC1260BL INFORMATION:

The blanket warming chamber contains an epoxy-coated 

blanket support assembly and one (1) shelf. The fl uid 

warming chamber is equipped with three (3) white, epoxy-

coated wire baskets to accommodate most commonly used 

surgical fl uids packaged in bags or bottles, mounted on 

basket rail supports. Each basket has a capacity of 18 1-liter 

bottles or 24 1-liter bags. The cabinet is furnished with a full 

perimeter rubber bumper assembly for exterior protection, 

and one (1) set of 5" (127mm) heavy-duty casters – two (2)

rigid and two (2) swivel with locking brake.

EC1540BL INFORMATION:

The blanket warming chamber contains an epoxy-coated 

blanket support assembly and two (2) shelves. The fl uid 

warming chamber is equipped with one (1) white, epoxy-

coated metal basket to accommodate most commonly used 

surgical fl uids packaged in bags or bottles, mounted on 

basket rail supports. The basket has a capacity of 30 1-liter 

bottles or 24 1-liter bags. The cabinet is furnished with one 

(1) set of 5" (127mm) heavy-duty casters – two (2) rigid and 

two (2) swivel with locking brake.

EC1730BL INFORMATION:

    WARNING

To prevent serious personal injury, death, or 

property damage: 
Do not steam clean, hose down or flood the 

interior or exterior with water or liquid solution 

of any kind. 

Do not use water jet to clean. Failure 

to observe this precaution will void the warranty.

(IP X0 - Listed as Ordinary)

DANGER

To prevent serious personal injury, death, 

or property damage:

Do not use this warming appliance in 

the presence of flammable anesthetic 

mixtures (with air or with oxygen or 

nitrous oxide). 

Not category AP or APG equipment 

Appliance Description and Intended Use

Summary of Contents for EC1260BL































Reviews: