Enttec 71520 User Manual Download

Page: 13 / 15

Pixel Octo User Manual

For latest version visit:

www.enttec.com

10 December 2019

M-files ID: 4836041

Page|

KiNET

The information provided is:

•

Total packets received

•

Discover supply packets received

•

Discover ports packets received

•

DMXOUT packets

•

KGet packets

•

KSet packets

•

PORTOUT Packets

•

Set device name packet received

•

Set device IP packet received

•

Set universe packets received

•

Last IP received from

•

Last port data received from

Update Firmware

It is strongly recommended that Pixel Octo is
updated with the latest firmware, available on the
ENTTEC website. This firmware can be loaded to the
driver through its web interface by carrying out the
following steps:

Browse and select the correct firmware
version on your PC

Press the Update Firmware button

Once the firmware update is complete, the device
will reboot while the web interface displays the
message shown in the image below

Reset to Factory Defaults

Using Web Interface

The reset to defaults command can be found under
the Settings tab of the Pixel Octo.

Once the command is pressed, a pop-up would
appear as shown in the image below:

Summary of Contents for 71520
















Search results

Summary of Contents for 71520

Reviews:

Related manuals for 71520

Brands by name

Popular brands

Enttec 71520, User Manual

Search results

Summary of Contents for 71520

Reviews:

Related manuals for 71520

Brands by name

Popular brands