Enviro E25 Series Owner'S Manual Download

Page: 4 / 43

Table of Contents

Safety Precautions...........................................................................................................2

Table of Contents.............................................................................................................4

Codes And Approvals.......................................................................................................5

Specifications..................................................................................................................6

Rating Label Location...........................................................................................6

Dimensions..........................................................................................................6

Install Depths.......................................................................................................6

E25 Options Dimensions......................................................................................6

Operating Instructions.....................................................................................................7

Lighting and Turning Off Instructions (IPI).............................................................7

Lighting and Turning Off Instructions (NOVA.)........................................................8

Remote Control Operations...................................................................................10

System Description.............................................................................................10

Technical Data....................................................................................................10

Transmitter..............................................................................................10

Integrated Fireplace Controller (IFC).....................................................................11

Accessing IFC.....................................................................................................12

Operating Procedure...........................................................................................13

Venturi

Adjusment...............................................................................................16

Operating Normal operating sounds......................................................................16

Maintenance And Service................................................................................................17

Glass Door Removal............................................................................................17

Cleaning the Painted Surfaces..............................................................................18

Cleaning the Glass..............................................................................................18

Cleaning the Firebox...........................................................................................18

Replacing the Glass.............................................................................................18

Check Pilot and Burner Flames.............................................................................18

Burner Removal..................................................................................................19

Fuel Conversion..................................................................................................20

Initial Installation...........................................................................................................22

Surround Assembly..............................................................................................23

Installing Surround On unit....................................................................................23

Clearances to Combustibles.................................................................................24

Minimum Fireplace Size.......................................................................................24

Venting...............................................................................................24

Exhaust Restrictor...............................................................................................26

Installing the E25..............................................................................................27

Horizontal termination..........................................................................................29

Zero Clearance Fireplace Installation...................................................................30

Electrical-Requirements............................................................................30

Proflame 2 wiring diagram....................................................................................31

Gas Line Connection...........................................................................................32

Adjusting The Pilot Flame....................................................................................33

Secondary Installation....................................................................................................31

Log Set Installation............................................................................................34

Trouble Shooting............................................................................................................37

Parts Diagram - Components..........................................................................................41

Parts List.......................................................................................................................40

Warranty.......................................................................................................................42

Installation Data Sheet...................................................................................................43

Summary of Contents for E25 Series












































Search results

Summary of Contents for E25 Series

Reviews:

Related manuals for E25 Series

Brands by name

Popular brands

Enviro E25 Series, Owner'S Manual

Search results

Summary of Contents for E25 Series

Reviews:

Related manuals for E25 Series

Brands by name

Popular brands