background image

 

11235 West Bernardo Court, Suite 102 

San Diego, CA   92127 

888-880-1880 

Fax:  707-281-0567 

EnvironmentalLights.com 

 

Copyright EnvironmentalLights.com 

 

All Rights Reserved  12/13/18 

 

24 Volt Single Color Super Flat LED Rope 

Part Numbers: SFR-XX-W-20, SFR-XX-B-20 

 

 

 

LED Super Flat Rope from Environmental Lights is a unique and special product you probably 
won't find anywhere else. It is rugged and waterproof, like LED rope, but is more compact and 
brighter. The face of the LED rope has a mask that hides the circuitry, so all you see is the LEDs. 
This mask is either white or black and matches the color of the sidewalls and back. Select either 
white or black finish (mask and sidewalls.) Single Color Super Flat Rope uses 60 very bright 
5050 (5.0 mm square) triplex LEDs. Best of all, Super Flat Rope is available in many colors and 
can be used in 20 meter (65.7 feet) lengths—just be sure to apply power to both ends. 
 
It is easy to customize and create impressive large scale effects using Super Flat LED Rope. 
Easy to dim or control using any of our LED dimming drivers, controllers or pulse dimmers. Or 
use any DMX controller, in conjunction with any of our decoders. This is a fantastic product for 
commercial, studio, architectural and decorative purposes. 

Based on the needs of the project, the length of Super Flat LED Rope can be customized. We 
provide all the tools, accessories, and instructions that are needed to customize your project. 
Channel for Single Color Super Flat LED Rope is easy to install. Simply use screws to mount the 
channel and then insert the Super Flat LED Rope. 

 

Summary of Contents for SFR-XX-B-20















Reviews: