background image

 
 
 
 
 

PROFILE-100 AXIAL EXTRACTOR FANS 
Suitable for bathroom applications 

 

Thank  you  for  placing  your  confidence  in  EnviroVent  by  buying  this  product.  It 
has been manufactured following current technical safety regulations, production 
and  quality  standards  as  laid  down  by  the  international  Quality  Standard  ISO 
9001. Please read this instruction booklet carefully before installing or starting up 
the  product.  It  contains  important  information  on  personal  and  user  safety 
measures  to  be  followed  whilst  installing,  using  and  carrying  out  maintenance 
work  on  the  equipment.  Once  the  product  has  been  installed,  please  pass  this 
booklet to the end user. 
 
Check  that  the  product  is  in  perfect  condition  while  unpacking.  Any  fault  or 
damage  caused  in  origin  is  covered  by  the  EnviroVent  guarantee.  Please  make 
sure  that  the  product  corresponds  to  the  one  you  have  ordered  and  that  the 
details on the instruction plate fulfil your requirements. 
 
 

IMPORTANT: 

 

BE  SURE  TO  HAVE  READ  AND  UNDERSTOOD  THESE  INSTRUCTIONS 
BEFORE BEGINNING THE INSTALLATION PROCESS 
 

SAFETY AND RECOMMENDATIONS 

 

  All wiring must comply  with Building Regulations and the current  I.E.E. Wiring 

Regulations (BS7671) or the equivalent standards for your country. 
The final installation should be examined and tested by a competent person. 
This fan is IP44 rated. 

 

  Do not install near sources of heat in excess of 40°C. 

 

  Position  the  fan  at  the  furthest  distance  from  the  main  source  of  air 

replacement in the room in order to achieve maximum airflow performance. 

 

 

This  appliance  is  not  intended  for  use  by  young  children  or  infirm  persons 
unless  they  have  been  adequately  supervised  by  a  responsible  person  to 
ensure  that  they  can  use  the  appliance  safely.  Young  children  should  be 
supervised to ensure that they do not play with the appliance.

 

 
 

Summary of Contents for PROFILE-100













Reviews: