Wireless Barcode Scanner
Quick Setup Guide
Reset toDefaults
Handset&Cradle
A Handset
①Data Indicator
（
Front
）
②Power Indicator
（
Back
）
③Trigger
④View window of capture
B Cradle, data relay and charging handset
⑤Indicator
⑥Pairing Button
⑦Channel Button
⑧Data & Power Interface
Installation
Step1.
Refer to the below pictures, connect the cradleto host (e.g. PC)
with different cables firstly
：
USB End
: Plug the RJ45 endinto cradle ⑧,and plug the other endto the
host.
USB cable
Keyboard
PS/2 End:
Plug the RJ45 to cradle
⑧
,and connect the male
PS/2 end to PC port and the female end with keyboard wire.
PS/2cable
RS232 End
：
RS232 cable RJ45 side to connect cradle
⑧
,the other side
to connect to PC. Power port on RS232 cable connect to power
adaptor(DC5V).
RS232
cable
Typically,the cradle will identify theinterface type automatically. In
extreme casescradle may need a manuallysetting if the host fails to
identify it. Please trigger the code below for manual setting.
Automatic Identification
(Default)
USB
PS/2
RS232
Note: The auto setting of interface type will only be activated when
the pairing is well done. Please refer to the Step2 and Step3 for pairing.
Step 2.
Put the handset onto the cradle, then pair the handset and
cradle: Press and hold cradle
⑥
for about 4 seconds,until the
handsetissued a "beep-beep-beep" sound.
Note:1 cradle can support maximum 100 handsets. The handset cannot
upload data if the handset and cradle were not well paired.
Usage of Scanner
Power On/Power off
Scanner will be power on when the trigger is pulled.When the scanner is
not operated for 30seconds,it will turn off automatically.
Code capture
In the standby mode, pull the trigger to capture code. Make sure
the red aiming line
is covering the full code.
Recharging
1, Place the handset onto the cradle to start recharging.
2, Using USB DC adapter or USB ports on PCas the power source, it can
be chargedby MicroUSB cable via interface at the handset bottom.
Note
：
1. When the handset is low power, the power
indicator
②
will beflashinggreen.
2.When the handset is recharging, the power indicator keeps
flashing red, and it turns yellow on when charging finishes.
Built-in Data Memory
In Auto-storing Mode, if the handset is out of contact distance limit
with the cradle,the captured code data will be saved into built-in
handset memory and the data indicator
①
turns red.The handset will
upload the codedata to the cradle automatically whenthe contact
connection comes back normal.Then the data indicator
②
turns green.
Multi-Cradles working
In case two or more cradles working in the same room, please set
them to different channels to ensure high upload efficiency as follow.
1. Open a notepad or any text editoron the host to display the channel
number.
2. Press the cradle Channel button
⑦
to change the channel number.
3. Put the handset onto the cradle. Press and hold the cradle
button
⑥
for about 4 seconds to pair the handset and cradle.
Remark: If two or more cradles working in the same signal channel, it
will slow down upload speed. However, they won’t jam with each other.
Indicator&Button
Scanner Indicator
Indicator
state
Meaning
Power
Indicator
(②Back)
Green
Started normally
Greenflash
Power low,need to recharge
Red flash
Recharging
Yellow
Recharge finished
Data
indicator
(①Front)
Green
All data uploaded
Red
Stored data pending to upload
Red flash
Data storage is full
Yellow flash
Data is uploading
Possibility of upload failures: Cradle disconnected to PC; Exceeding
distance limit; Handset working in Manual Upload Mode (stock check).
①
②
③
⑤
⑥
⑦
④
⑧
□
A
□
B
