background image

EOS Zeus S / EOS Zeus SL - Installation and Operating Instructions

EN-3

Contents

 Documentation

..................................................................................................EN-2

1

General safety instructions

..........................................................................EN-5

1.1

Safety levels................................................................................................EN-5

1.2

Mounting and electrical installation .................................................EN-6

1.3

Operator instruction................................................................................EN-9

1.4

Standards and regulations................................................................. EN-10

2

Identification

.................................................................................................... EN-11

2.1

Requirements for operation  ............................................................. EN-11

2.2

Nameplate ............................................................................................... EN-11

2.3

Scope of delivery ................................................................................... EN-12

2.4

Intended use ........................................................................................... EN-13

2.5

Technical data ........................................................................................ EN-14

3

Installation

........................................................................................................ EN-17

3.1

Specifications for the cabin ............................................................... EN-17
3.1.1

Installation site  ...................................................................... EN-18

3.1.2

Air inlets and outlets ............................................................ EN-19

3.1.3

Connection cable .................................................................. EN-22

3.2

Temperature sensor  ............................................................................ EN-22

3.3

Installing the heater ............................................................................. EN-23

3.4

Installing the heater guard rail (optional) .................................... EN-25

4

Connections

...................................................................................................... EN-31

4.1

General instructions for electrical installation ............................ EN-31

4.2

Connections ............................................................................................ EN-31
4.2.1

Terminal diagram 6 kW/7.5 kW/9 kW ............................ EN-32

4.2.2

Terminal diagram 10.5 kW/12 kW ................................... EN-33

4.2.3

Internal wiring 6 kW–12 kW .............................................. EN-33

4.2.4

Establishing an electrical connection ............................ EN-35

4.3

Heating time limitation....................................................................... EN-36

Summary of Contents for 94 7371 01

























































Reviews: