background image

2  /  THE BASICS

8 /  512

Reticle

HWS RETICLE ADVANTAGE
EOTECH’s Holographic technology provides a distinct advantage over typical red 

dots  EOTECH can offer any type of reticle pattern, as opposed to being limited to 

a single dot  EOTECH reticle designs are fabricated so that they can incorporate 

multiple trajectory points of aim, range assist features, and anti-torque or cant visual 

indicators 

HWS RETICLE PATTERN
EOTECH’s reticle patterns greatly impact accuracy and fast target acquisition  

EOTECH’s reticle patterns feature a 68 MOA ring surrounding a 1 MOA center dot, 

allowing the shooter to quickly pick up a target; HWS allows for more complex 

reticle designs with minimal parallax error 

0 RETICLE
The 68 MOA ring with 1 MOA dot is ideal for fast target 

acquisition  It provides three usable aiming points  The 

aiming points above were based on the following load:  

 223 Cal  62 Gr  2,900 Vel  Other loads and calibers can 

also be used, but the operator will have to establish the 

ranges associated with the aiming points  When using a 

shotgun, the 68 MOA ring can be used to represent shot 

patterns, but will vary based on choke and shell selection 

50 yds  

and 

200 yds 

7 yds 

Summary of Contents for 512



























Reviews: