BEIJING EPSOLAR TECHNOLOGY CO., LTD. Tel: +86-10-82894112 / 82894962 Website:www.epsolarpv.com/www.epever.com
1
2
LandStar GPLI series solar charge controller
——
With built in LED driver of step-down voltage
1. Safety Information
Read all of the instructions in the manual before installation.
DO NOT disassemble or attempt to repair the controller.
Install external fuse or breaker as required.
Do disconnect the solar module and fuse/ breakers near to battery before
installing or moving the controller.
Power connections must remain tight to avoid excessive heating from a
loose connection.
Only charge batteries that comply with the parameters of controller.
Battery connection may be wired to one battery or a bank of batteries.
2.
Overview
Thank you for selecting the LandStar GPLI series step-down voltage control
solar charge controller with built in LED driver. It combines solar charge
controller and LED constant current driver into one unit which is ideal for solar
LED lighting, especially when dimmer function is needed. Full waterproof and
IR communication design, it has the feature of high efficiency, high control
accuracy and dimmer function. The product is dedicated in LED indoor and
outdoor lighting application condition, such as road lighting, landscape lighting
and billboard lighting etc.
Product Features:
Maximum output efficiency of 96%
Without any button, parameter setting via Mobile APP and RC-01 with IR
function
Flexible dimmer function, 0
～
100% can be adjusted
Multiple load control modes, LED rated current and current percentage can
be set.
Load test function for detecting the system, the controller power on, the load
is ON.
Aluminum housing for better cooling
Fully encapsulated PCB, IP68 protection (1.5 meters, 72h)
Long lifespan design
3.
Product Features
①
Mounting hole size
⑥
Battery Positive and Negative
Wires
②
Charging Status LED indicator
⑦
Load Positive and Negative
Wires
③
Battery Status LED indicator
⑧
Infrared LED
④
Temperature Sensor
※
⑨
Infrared Receiver Module
⑤
PV Positive and Negative Wires
※
Temperature sensor is short circuit or open circuit, the controller will
charge or discharge battery for 25
℃
and no temperature compensation
4. Wiring
Reference for Serial connection of LED
System Voltage
Serial connection
Max. Load Output Voltage
12V
1
～
3 LED
Min. V
BAT
-0.5V(LS102480GPLI)
Min. V
BAT
-1V(LS2024100GPLI)
24V
1
～
6 LED
NOTE:
The above one LED (1W, 3V) are calculated. If the user uses
the unconventional LED, The actual LED voltage must less than the
Max. Load Output Voltage.
Connection Order
1) Connect components to the charge controller in the sequence as shown
above and pay much attention to the “+” and “-”. Please don’t insert the fuse or
turn off the breaker during the installation. When disconnecting the system, the
order will be reserved.
2)
After power on the controller, check battery LED indicator ( the LCD on).
Otherwise please refer to chapter 9
.
3)
Connecting a fuse in series through battery positive (+) in the circuit and the
battery circuit fuse must be 1.25 to 2 times to the rated current. The installed
distance is within 150mm.
Load self-test function
The load is ON when the controller power on 10seconds. After 10 seconds it
will restore to set working mode.
5. LED Indicators
Indicator
Color
Status
Instruction
Green
On Solid
PV connection normal
but low
voltage(irradiance) from
PV, no charging
Green
OFF
No PV voltage(night
time) or PV connection
problem
Green
Slowly Flashing(1Hz)
In charging
Green
On Solid
Normal
Green
Slowly Flashing(1Hz)
Full
Green
Fast Flashing(4Hz)
Over voltage
Orange
On Solid
Under voltage
Red
On Solid
Over discharged
Red
Slowly Flashing(1Hz)
Battery Overheating
Charging (green) and battery indicator (red)
flashing simultaneously
System voltage error
6.
Setting Operation
7. Load Working Mode
1) Manual Mode
2) Light ON/OFF (Default)
3) Light + ON Timer
Light + ON Timer1 Light + ON Timer2
Figure 1 Product Feature
Figure 2 Wiring
Thank you for selecting the LandStar GPLI series solar charge
controller with built-in LED driver of a step-down voltage control.
Please read this manual carefully before using the product and pay
attention to the safety information.
图 3 设置操作
注：具体设置方法详见
手持设备说明书。
There are two methods that it can realize
controller work mode and parameters through
IR function:
1）
Infrared Communication Remoter
—RC-01
Set parameters of three timer, the LED rated
current percentage and battery type, etc.
2) Ir-Android-Micro
—IAM, Mobile and APP.
APP software can be downloaded from the
website of
④
①
②
③
⑥
⑤
⑦
⑧
⑨
