manualshive.com logo in svg

epiphan video Standalone VGA Grid, User Manual

The Epiphan Standalone VGA Grid is a cutting-edge hardware device that allows users to connect multiple VGA sources to a single display. You can easily set up and operate this device with the help of our comprehensive User Manual, available for free download on our website. Unlock the full potential of your Epiphan Standalone VGA Grid with our detailed instructions and troubleshooting tips, seamlessly accessible at 88.208.23.73:8080.

Share
Download
background image

Standalone VGA Grid User Guide
                                     

Force the capture card to use a specific EDID

Like monitors, each video capture card in theStandalone VGA Grid contains an EDID. When you connect a 
VGA or DVI video source (such as a laptop or video camera), this source sees the Standalone VGA Grid's HD 
Encoder's capture card as a monitor and uses its EDID to negotiate which video signal to send. 

Generally the capture card's DVI input correctly emulates a monitor that supports your video source. 
However sometimes, particularly if your source uses a custom set of display properties, you need to help 
Standalone VGA GridHD Encoder by uploading a custom EDID to force the capture card to report that it 
emulates a resolution, color depth, etc needed by your laptop, camera or other video source.

Upload a new EDID

In most circumstances the factory installed default EDID, is sufficient. However, there may be some cases 
where a video source  uses resolutions that you do not want to use.  In that case you can choose an EDID that 
forces the Standalone VGA Grid's capture card to use a specific set of attributes.

The uploaded EDID is permanently installed on your system and this capture card (a "Source" in the web 
interface) will always share the uploaded EDID with the connected video input source.

EDID changes are permanent until you replace them with another EDID or specifically choose to 
restore the facotry EDID for a given source. Not even a system-level factory reset removes the 
configured EDIDs.

 1.  To download a new EDID file, go to the 

Epiphan support

 web page. The support page opens.

 2.  Select the support page for Standalone VGA Grid.

 3.  Scroll to the 

EDID 

section.

 4.  Click on an EDID from the list. The file is saved to your downloads folder on your hard drive.

 5.  Connect to the admin interface using your preferred connection mechanism. See 

Connect to the admin 

interface

.

 6.  Login as admin.

 7.  From the web interface, Scroll to the 

Sources 

section.

 8.  Click the name of the DVI capture card (source) for which you want to upload an EDID; the 

Source Configuration page opens.

 9.  Scroll to the 

EDID upload

 section. 

139

Summary of Contents for Standalone VGA Grid
































































































































































































































































































































Reviews:

No comments

Related manuals for Standalone VGA Grid

GCAN 4055 User Manual preview
4055
Brand: GCAN Pages: 16
xDuoo X20 Manual preview
X20
Brand: xDuoo Pages: 17
Magnavox AZ1100 - Single Deck Istruzioni Per L'Uso preview
AZ1100 - Single Deck
Brand: Magnavox Pages: 16
Magnavox NB500MG9 Owner'S Manual preview
NB500MG9
Brand: Magnavox Pages: 50
Magnavox NB500MG1F - Blu-Ray Disc Player Specifications preview
NB500MG1F - Blu-Ray Disc Player
Brand: Magnavox Pages: 2
Magnavox AZ 8006 Owner'S Manual preview
AZ 8006
Brand: Magnavox Pages: 16
Magnavox MBP5320 Setup Manual preview
MBP5320
Brand: Magnavox Pages: 2
Magnavox MBP5230 Owner'S Manual preview
MBP5230
Brand: Magnavox Pages: 81
Magnavox MBP5130 Owner'S Manual preview
MBP5130
Brand: Magnavox Pages: 52
Magnavox MBP5120F Quick Start Manual preview
MBP5120F
Brand: Magnavox Pages: 2
Magnavox MBP5210 Specifications preview
MBP5210
Brand: Magnavox Pages: 2
Magnavox MBP1100 - Manual D'Utilisation preview
MBP1100 -
Brand: Magnavox Pages: 52
Magnavox \ Quick Start Manual preview
\
Brand: Magnavox Pages: 8
Magnavox AZ1307 - Portable Radio Cass Rec Bruksanvisning preview
AZ1307 - Portable Radio Cass Rec
Brand: Magnavox Pages: 18
Magnavox AZ1100 - Single Deck Manual De Instruções preview
AZ1100 - Single Deck
Brand: Magnavox Pages: 14
Magnat Audio MCD1050 Important Notes For Installation & Warranty Card preview
MCD1050
Brand: Magnat Audio Pages: 32
Magnavox AZ6843 - Portable Cd-player Manual Del Usuario preview
AZ6843 - Portable Cd-player
Brand: Magnavox Pages: 20
NAD S500i Owner'S Manual preview
S500i
Brand: NAD Pages: 32

Brands by name

Popular brands

Load more brands