epiphan video Standalone VGA Grid User Manual Download | Manualshive

Page: 163 / 319

background image

Standalone VGA Grid User Guide

Restrict viewers by IP address

Restrict viewers by IP address

The Standalone VGA Grid permits you to restrict which computers can access broadcasts by building a list of
allowed and/or denied IP addresses. You can do this at a global level for the system and can also override
these settings on a per-channel basis. Both global and per-channel configuration procedures are described
below.

IP address restriction is valid for the viewer only and does not affect the web admin interface or
the mobile configuration interface.

If your viewer account has a password, your viewers must connect to the system from a computer (or
gateway) with a permitted IP address and must also supply the username (viewer) and password before they
can view the broadcast.

To restrict access by IP address you need to know the IP addresses, or range of addresses for your viewers. By
default all IP addresses are allowed to connect to the broadcast.

If you’re not familiar with creating allow/deny lists, refer to the examples below this procedure for assistance
with crafting your lists.

To restrict viewers by IP address:

1. Connect to the admin interface using your preferred connection mechanism. See

Connect to the admin

2. Login as admin.

3. Select the

Access passwords

link in the Configuration menu; the password configuration page opens.

4. Type allowed IP addresses or address ranges in the

Allow IP’s

field. Separate addresses with a comma.

5. Type denied IP addresses or address ranges in the

Deny IP’s

field. Separate addresses with a comma.

6. Click

Apply

.

To restrict viewers of a specific channel by IP address:

1. Connect to the admin interface using your preferred connection mechanism. See

Connect to the admin

2. Login as admin.

3. Select the

Streaming

link for the desired channel; the streaming configuration page opens.

4. From the

Access Control

drop-down, select

Use these Settings

; local password and Allow/Deny IP

lists are enabled.

5. If desired, type a password for the viewer in the

Viewer Password

field.

6. Type allowed IP addresses or address ranges in the

Allow IP’s

field. Separate addresses with a comma.

163

«
...
161
162
163
164
165
...
»

Summary of Contents for Standalone VGA Grid
































































































































































































































































































































Reviews:

No comments

Related manuals for Standalone VGA Grid

Brand: Z3 Technology Pages: 18

Brand: Z3 Technology Pages: 23

Brand: Kramer Pages: 14

Brand: Rotel Pages: 6

Brand: Samy Pages: 36

Brand: iBasso Pages: 16

Brand: GOLD LABEL Pages: 5

Brand: Bronson++ Pages: 50

Brand: FUNAI Pages: 2

LaCinema Premier

Brand: LaCie Pages: 24

Brand: Laser Pages: 22

Brand: Oakcastle Pages: 20

TViX HD M-4000P

Brand: Dvico Pages: 59

Black Sea MP001

Brand: SWEEX Pages: 6

Brand: M-Audio Pages: 36

SLSW860 - PORT. CD PLAYER

Brand: Panasonic Pages: 8

SLJ610V - PORTABLE CD PLAYER

Brand: Panasonic Pages: 8

SLCT780 - PORT. CD PLAYER

Brand: Panasonic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands