epiphan video Standalone VGA Grid User Manual Download | Manualshive

Page: 238 / 319

background image

Standalone VGA Grid User Guide

AFU or copy to USB drive

If a conflict is reported regarding the Automatic file upload, go to the Automatic File Upload
configuration page and disable automatic file upload or switch it to a non-USB based
upload type. Repeat the steps above.

7. Insert the properly formatted USB drive into one of the system’s USB ports; the drive is recognized and

the transfer begins. If the drive has an activity indicator light, it flashes during the transfer.

8. When the activity light stops flashing, remove the USB drive.

9. If your USB drive does not have activity indicators:

a. Check the

Recording

list for each channel and the

Recorded Files

list for each recorder to

verify if there are files that have yet to be copied.

b.

Safely eject the USB drive

when you are satisfied all files have been copied, or if you see the USB

drive is out of storage space (

View available USB storage space

).

Manually copy recorded files to USB drive

You can manually copy recorder files to a USB drive connected to the Standalone VGA Grid.

This procedure is separate from automatic file upload and does not need any pre-configuration in the
automatic file upload page.

To manually copy recorded files to a USB drive:

1. Connect to the admin interface using your preferred connection mechanism. See

Connect to the admin

2. Login as admin.

3. Select the

External USB Drive link

in the Configuration section; the External USB Drive configuration

page is displayed.

4. Select

used to manually move/copy selected files via web interface

from the drop down list.

5. Click

Apply

; the changes are saved.

238

«
...
236
237
238
239
240
...
»

Summary of Contents for Standalone VGA Grid
































































































































































































































































































































Reviews:

No comments

Related manuals for Standalone VGA Grid

Brand: Eminent Pages: 31

Brand: Linear Technology Pages: 22

Brand: Clas Ohlson Pages: 52

Brand: FUNAI Pages: 53

Brand: Agilent Technologies Pages: 122

Brand: American Audio Pages: 2

Brand: Denver Pages: 86

RASPTOUCH ES9018K2M

Brand: Audiophonics Pages: 30

AZ7000 - Cd Personal

Brand: Magnavox Pages: 22

ROTAPULS CK61 Series

Brand: Lika Pages: 2

Brand: PRIZM Pages: 7

Brand: Hagerman Audio Labs Pages: 6

Brand: LC Pages: 44

Brand: Uhlenbrock Elektronik Pages: 4

Brand: AV Access Pages: 20

Brand: Tesla Pages: 19

Multi-Decoder MD-2

Brand: tams elektronik Pages: 40

Brand: Memorex Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands