page | 6
Support 866.838.5052
DEFAULT DEVICE FILE
Preset #
Preset
Name
Input
Mode
Output
(Voltage)
Speaker Hookup Configuration/
Comments
Additional Notes/Comments
5
ST4_HS10
Stereo**
Channel 1=8/4
Ω
LS-HS SUB10 subwoofer (e.g. 8Ω)
connected to channel 1
If desired, 2 subwoofers can be used in
parallel connection.
LS-SAT-4 satellites in 70V tap settings
connected to channel 2
**Front level potentiometers can be used
to raise or lower the subwoofer level
(Channel 1) relative to the level of the
satellite speakers (Channel 2).
Channel 2=70V
**Must use supplied input summing cable
DSP settings for “flat response” tonal
balance
6
ST6_HS10
Stereo**
Channel 1=8/4
Ω
LS-HS SUB10 subwoofer (e.g. 8Ω)
connected to channel 1
If desired, 2 subwoofers can be used in
parallel connection.
LS-SAT-6 satellites in 70V tap settings
connected to channel 2
**Front level potentiometers can be used
to raise or lower the subwoofer level
(Channel 1) relative to the level of the
satellite speakers (Channel 2).
Channel 2=70V
**Must use supplied input summing cable
DSP settings for "flat response" tonal
balance
7
ST8_HS10
Stereo**
Channel 1=8/4
Ω
LS-HS SUB10 subwoofer (e.g. 8Ω)
connected to channel 1
If desired, 2 subwoofers can be used in
parallel connection.
LS-SAT-8 satellites in 70V tap settings
connected to channel 2
**Front level potentiometers can be used
to raise or lower the subwoofer level
(Channel 1) relative to the level of the
satellite speakers (Channel 2)
Channel 2=70V
**Must use supplied input summing cable
DSP settings for “flat response” tonal
balance
8
S4HS10_8
Stereo**
Channel 1=8/4
Ω
LS-HS SUB10 subwoofer (e.g. 8Ω)
connected to channel 1
If desired, 2 subwoofers can be used in
parallel connection.
LS-SAT-4 satellites in 8Ω tap setting
connected to channel 2
Maximum of 4 satellites may be wired in
parallel per channel
Channel 2=8/4
Ω
**Must use supplied input summing cable
**Front level potentiometers can be used
to raise or lower the subwoofer level
(Channel 1) relative to the level of the
satellite speakers (Channel 2).
DSP settings for “flat response” tonal
balance
9
S6HS10_8
Stereo**
Channel 1=8/4
Ω
LS-HS SUB10 subwoofer (e.g. 8Ω)
connected to channel 1
If desired, 2 subwoofers can be used in
parallel connection.
LS-SAT-6 satellites in 8Ω tap setting
connected to channel 2
Maximum of 4 satellites may be wired in
parallel per channel
Channel 2=8/4
Ω
**Must use supplied input summing cable
**Front level potentiometers can be used
to raise or lower the subwoofer level
(Channel 1) relative to the level of the
satellite speakers (Channel 2).
DSP settings for “flat response” tonal
balance
10
S8HS10_8
Stereo**
Channel 1=8/4
Ω
LS-HS SUB10 subwoofer (e.g. 8Ω)
connected to channel 1
If desired, 2 subwoofers can be used in
parallel connection.
LS-SAT-8 satellites in 8Ω tap setting
connected to channel 2
Maximum of 4 satellites may be wired in
parallel per channel
Channel 2=8/4
Ω
**Must use supplied input summing cable
**Front level potentiometers can be used
to raise or lower the subwoofer level
(Channel 1) relative to the level of the
satellite speakers (Channel 2).
DSP settings for “flat response” tonal
balance
11
ST4_SB12
Stereo**
Channel 1=8/4
Ω
LS-BSUB-12 subwoofer (e.g. 8Ω) connected
to channel 1
If desired, 2 subwoofers can be used in
parallel connection.
LS-SAT-4 satellites in 70V tap settings
connected to channel 2
**Front level potentiometers can be used
to raise or lower the subwoofer level
(Channel 1) relative to the level of the
satellite speakers (Channel 2).
Channel 2=70V
**Must use supplied input summing cable
DSP settings for “flat response” tonal
balance
