DISASSEMBLY, ASSEMBLY, AND ADJUSTMENT
REV.-A
4. Depress the ON LINE switch, so that only the new selected pattern is printed again.
5. Confirm the printed pattern. If it is not OK, return to STEP 3.
Example: [Present] VR1 = -3 (Pattern 2)
Depress the LF switch two times.
VR2 = - 1 (Pattern 4)
6. Rotate VR1 until the buzzer sounds.
7. Turn the power off.
LQ Mode Adjustment
LQ mode adjustment is similar to the one for draft mode.
1 . Turn the power on while depressing the ON LINE, FORM FEED (FF), and LINE FEED (LF) switches.
2. Depress the FF switch, so that the test pattern is printed. The test pattern prints four patterns, and the
value of the position where VR2 is becomes the center. (Refer to Figure 4-39.)
Example: VR2 = +9 (Pattern 3)
Figure 4-39. Test Pattern Printing (LQ Mode)
3. Check and select the most aligned pattern.
If the selected pattern is above the center, depress the FF switch an applicable number of times (once or
twice). (Refer to Table 4-6.)
If the selected pattern is lower than the center, depress the LF switch an applicable number of times
(once or twice). (Refer to Table 4-6.)
Example: The most aligned pattern is VR2 = + 7 (Pattern 1). So, depress the FF switch two times.
4. Depress the ON LINE switch, so that only the new selected pattern is printed again.
5. Confirm the printed pattern. If it is not OK, return to STEP 3.
Example: [Present] VR2 = +7 (Pattern 1)
4 Depress the FF switch one time.
VR2 = +6
6. Rotate VR2 until the buzzer sounds. (Position VR2 to the value of the new selected pattern.)
7. Turn the power off.
4-28
LQ-500/L-1000
Summary of Contents for ActionPrinter L-1000
