Epson C11CG28201 User Manual Download | Manualshive

Page: 295 / 305

background image

295

• Do not use aerosol products that contain flammable gases inside or around the product. Doing so may

cause fire.

• Do not press too hard on the document table when placing originals.

• Do not open the scanner section while the product is copying, printing, scanning, or performing any

other functions.

• Be careful not to trap your fingers when closing the document cover or scanner.

• Except as specifically explained in your documentation, do not attempt to service or disassemble the

product yourself.

• Unplug the product and refer servicing to qualified service personnel under the following conditions: if

the power cord or plug is damaged; if liquid has entered the product; if the product has been dropped
or the case damaged; if the product does not operate normally or exhibits a distinct change in
performance. Adjust only those controls that are covered by the operating instructions.

• Leave the ink cartridges installed. Removing the cartridges can dehydrate the print head and may

prevent the product from printing.

• Before transporting the product, make sure that the print head is in the home (far right) position and

the ink cartridges are in place.

• When storing or transporting the product, do not tilt it, stand it on its side, or turn it upside down;

otherwise ink may leak.

Parent topic:

Important Safety Instructions

Ink Cartridge Safety Instructions

• Keep ink cartridges out of the reach of children and do not drink the ink.

• Be careful when you handle used ink cartridges; there may be ink remaining around the ink supply

port. If ink gets on your skin, wash it off with soap and water. If it gets in your eyes, flush them
immediately with water.

• Do not put your hand inside the product or touch any cartridges during printing.

• Install a new ink cartridge immediately after removing an expended one. Leaving cartridges

uninstalled can dry out the print head and may prevent the product from printing.

• Do not remove or tear the label on the cartridge; this can cause leakage.

• Do not remove the transparent seal from the bottom of the cartridge. This may cause the cartridge to

become unusable.

• Do not break the hooks on the side of the cartridge when removing it from the packaging.

• Do not touch the green IC chip on the side of the cartridge. This may prevent normal operation.

«
...
293
294
295
296
297
...
»

Summary of Contents for C11CG28201


















































































































































































































































































































Reviews:

No comments

Related manuals for C11CG28201

Brand: Oki Pages: 282

Brand: IBM Pages: 334

Brand: IBM Pages: 428

Brand: IBM Pages: 316

Brand: IBM Pages: 210

DocuPrint C3055 DX

Brand: Xerox Pages: 20

Aficio MP C6503SP

Brand: Ricoh Pages: 264

Brand: Xerox Pages: 418

Brand: Roland Pages: 44

Brand: Xerox Pages: 78

Brand: Unisys Pages: 144

Brand: Sagem Pages: 154

Brand: Sam4s Pages: 24

Brand: Sharp Pages: 38

Brand: Xerox Pages: 34

Brand: Infinite Peripherals Pages: 2

Brand: WOOSIM Pages: 67

WorkCentre 7232

Brand: Xerox Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands