Confidential
Confidential
7.
7. In order to prot
In order to protect sensiti
ect sensitive microp
ve microprocess
rocessors and circu
ors and circuitry, use stat
itry, use static discharg
ic discharge equipme
e equipment, such as anti-s
nt, such as anti-static
tatic
wrist straps, when accessing
wrist straps, when accessing internal components.
internal components.
8.
8. Do not tilt this prod
Do not tilt this product immed
uct immediately af
iately after initia
ter initial ink charge
l ink charge, especial
, especially after per
ly after performi
forming the ink charg
ng the ink charge several
e several
times. Doing so may cause ink to leak from the product because it
times. Doing so may cause ink to leak from the product because it may take some time for the waste ink pads
may take some time for the waste ink pads
to completely absorb ink wasted due
to completely absorb ink wasted due to the ink charge.
to the ink charge.
9.
9. Never to
Never touch the ink o
uch the ink or wasted in
r wasted ink with bare ha
k with bare hands. If ink co
nds. If ink comes into co
mes into contact with y
ntact with your skin
our skin, wash it off wit
, wash it off with
h
soap and water immediately. If you have
soap and water immediately. If you have a skin irritation, consult a
a skin irritation, consult a doctor immediately.
doctor immediately.
10.
10. When disassembling or
When disassembling or assembling this product,
assembling this product, make sure to wear
make sure to wear gloves to avoid inju
gloves to avoid injuries from metal parts
ries from metal parts
with sharp edges.
with sharp edges.
11.
11. Use only recommen
Use only recommended tools for
ded tools for disassembling, assembling or ad
disassembling, assembling or adjusting the printer.
justing the printer.
12.
12. Observ
Observe the specified torqu
e the specified torque when tightenin
e when tightening screws.
g screws.
13.
13. Be extremely carefu
Be extremely careful not to scratch
l not to scratch or contaminate the
or contaminate the following parts.
following parts.
Nozzle plate of the printhead
Nozzle plate of the printhead
CR Scale
CR Scale
PF Scale
PF Scale
Coated surface of the PF Roller
Coated surface of the PF Roller
Gears
Gears
Rollers
Rollers
LCD
LCD
Scanner Sensor
Scanner Sensor
Exterior parts
Exterior parts
14.
14. Never use oil or grease other than
Never use oil or grease other than those specified in this manual. Use of diff
those specified in this manual. Use of different types of oil or grease may
erent types of oil or grease may
damage the component or give bad influence on
damage the component or give bad influence on the printer function.
the printer function.
15.
15. Apply the
Apply the specified amount
specified amount of grease
of grease described in
described in this manual.
this manual.
16.
16. Make the
Make the specified adjustments
specified adjustments when you
when you disassemble the p
disassemble the printer.
rinter.
17.
17. When cleaning this
When cleaning this product, follow th
product, follow the procedure d
e procedure described in this manu
escribed in this manual.
al.
18.
18. When transporting this prod
When transporting this product after filling the ink in the prin
uct after filling the ink in the printhead, pack the printer withou
thead, pack the printer without removing the
t removing the
ink cartridges in order to prevent t
ink cartridges in order to prevent the printhead from drying out.
he printhead from drying out.
19.
19. Make sure to in
Make sure to install antivirus software in th
stall antivirus software in the computers used
e computers used for the service su
for the service support activities.
pport activities.
20.
20. Keep the v
Keep the virus pattern f
irus pattern file of antiv
ile of antivirus software up
irus software up-to-date.
-to-date.
21.
21. When disassembling/reassembling th
When disassembling/reassembling this product, if y
is product, if you find adh
ou find adhesive power of
esive power of the double-sided tape
the double-sided tape which
which
secure the parts or FFC is not enough, replace the tape with new one and attach it correctly to the specified
secure the parts or FFC is not enough, replace the tape with new one and attach it correctly to the specified
points where the parts or FFC shou
points where the parts or FFC should be secured.
ld be secured.
22.
22. Unless otherwise specified in
Unless otherwise specified in this manual, the lab
this manual, the labels attached on the
els attached on the returned product
returned product should be transferr
should be transferred to
ed to
the corresponding attachment positions on the new
the corresponding attachment positions on the new one referring to the labels on the
one referring to the labels on the returned product.
returned product.
