8
Close the ink tank cover.
9
Connect the power cord to the back of the product and to
an electrical outlet.
Caution:
Do not connect to your computer yet.
10
Press the power button to turn on the product.
Note:
If an error message appears, turn off the product and
check that no protective material has been left inside the
product.
11
Select your language, country, date, and time settings.
Note:
You can change these settings later using the product’s
control panel. For more information, see the online User’s Guide.
Follow steps 12 and 13 to continue ink charging.
12
When the message to see the Start Here sheet appears
on the LCD screen, press and hold the
help button for
5 seconds.
13
When the ink confirmation message appears on the LCD
screen, select
Done to start charging the ink. Ink charging
takes approximately 11 minutes. A message appears
when ink charging is complete.
Caution:
Do not unplug or turn off the product, lift the printer
cover, or load paper while the product is charging or you’ll waste
ink.
Note:
After some ink is used for charging, the rest is available for
printing.
14
Follow the on-screen instructions to adjust the print
quality.
Note:
You need to load paper before you can adjust the print
quality. See “Load paper” for details.
IMPORTANT: Before using this product, make sure you read
these instructions and the safety instructions in the online User’s
Guide.
Important Safety Instructions:
When using telephone equipment, you
should always follow basic safety precautions to reduce the risk of fire,
electric shock, and personal injury, including the following:
• Do not use the Epson
®
product near water.
• Always keep this guide handy.
• Avoid using a telephone during an electrical storm. There may be a
remote risk of electric shock from lightning.
•
Do not use a telephone to report a gas leak in the vicinity of the leak.
Caution:
To reduce the risk of fire, use only a No. 26 AWG or larger
telecommunication line cord.
1
Unpack
Make sure you keep the box shown above for use when
transporting the printer.
Caution:
Do not lift the product by gripping the scanner unit. Make
sure you lift using the handholds on the bottom of the product.
Note:
Do not open the ink bottles until you are ready to fill the ink
tanks. The ink bottles are vacuum packed to maintain reliability.
1
Lift the printer cover until it clicks into place.
2
Remove all protective materials from the product.
Caution:
Do not touch the flat white cable, translucent film, or
ink tubes.
3
Close the printer cover.
Note:
Do not connect the power cord yet.
2
Fill ink tanks
Warning:
Keep the ink bottles out of the reach of children and do not
drink the ink.
Caution:
This product requires careful handling of ink. If ink spills,
wipe it off immediately with a damp towel to avoid permanent stains.
If ink gets on your clothes or belongings, it may not come off.
Note:
• Epson cannot guarantee the quality or reliability of third-party ink.
• Use the ink bottles included with the printer to set up the product.
Part of the ink will be used to charge the print head. These bottles
will print fewer pages compared with replacement ink bottles.
• The included ink bottles are designed for reliable printer setup and
cannot be resold.
Epson recommends the use of Genuine Epson 524 pigment
inks. The use of any other inks may cause damage not covered
by the warranty, particularly if they are not pigment. Epson
cannot guarantee that non-Epson 524 inks are pigment, even if
labeled as compatible.
1
Open the ink tank cover, then open the cap for the
black ink tank.
Note:
Refer to the color-coded sticker on the ink tank unit to
identify the color of each tank.
2
Unpack the black (BK) ink bottle. Hold the ink bottle
upright and slowly turn the bottle cap to remove it.
Caution:
Do not shake or squeeze the ink bottle. Do not touch
the top of the ink bottle after its cap is removed.
3
Insert the ink bottle into the filling port.
Note:
Do not force the bottle into position; each bottle is keyed
for each color.
4
Wait for the ink to fill the tank. Do not squeeze the bottle
or allow it to contact any other surface.
Note:
Ink flows into the tank and stops automatically when the
ink is filled to the upper line. If ink does not flow from the bottle,
lift and reinsert the bottle.
5
When the ink tank is full, remove the ink bottle
and securely close it with the cap. If any ink
remains in the bottle, store it for later use.
Note:
Do not leave the ink bottle inserted; otherwise
the bottle may be damaged or ink may leak.
6
Close the black ink tank cap.
7
Repeat the previous steps for the other colors.
Start Here
L6490
4141073 Rev.0
1-F
PMS012U
4141073 Rev.0
1-F
K
