EPSON Stylus Pro 4400/4450/4800/4880/4880C
Revision C
Product Description
Operating Panel
74
Details of each setting items
Note *1: Cutting Method setting items in the driver are slightly different from that of the panel default setting. The driver settings are as follows.
“Cut Method”
:
SN m1=80h(Cut Method) SN m1=81h(Cut Pressure)
Standard
:
m2=00h(Printer Table)
m2=00h(Printer Table)
Thin Paper
:m2=02h(Half-speed star wheel)m2=49h (Duty:70%300gf)
Thick Paper,Fast
:m2=01h(Standard 2 levels)m2=7Eh (Duty:125% 700gf)
Thick Paper,Slow
:m2=06h(Low-speed star wheel)m2=65h (Duty:100% 500gf)
*2: EX1B command is transmitted and registered in the media table in increments of 1msec. Inputting in increments of 100 msec is available when using the panel or utility. The
setting value is displayed in increments of 100 msec rounding off fractions.
Note 1: Value set by EX 1B command is similar to the above parameters.
2: If value other than parameters above or value out of range is set by EX 1B command, set by replacing with values below.
• PG setting
: Standard: m2=03h (PG Little – 1.2mm)
• Cutting method
: Standard m2=03h m2=49h
• Paper feed adjustment : 0% SN
m2=65h
• Eject paper roller set
: AUTO
m2=00h
• Ink drying time : 0 sec.
• Paper suction : Standard m2=33h (100%)
• MW print adjustment: n2:00h
Table 1-33. Details of each setting items
Setting
Operation
Setting value
PG setting
Enter any PG position.
• SN
m1 = 01h
• Wider m2 = 01h (PG Big: 2.1mm)
• Standardm2 = 03h (PG Little: 1.2mm)
• Widestm2 = 05h (PG Maximum: 2.6mm)
• Wide m2 = 02h (PG Middle: 1.5mm)
• Narrowm2 = 04h (PG Minimum: 0.7mm)
Cutting method
Cutting method is selected when cutting paper.
• SN
m1 = 80h
• Standardm2 = 03h
*1
m2 = 65h
• Thick paper, Fastm2 = 01hm2 = 7Eh
• SN
m1 = 81h
• Thin paperm2 = 02hm2 = 49h
• Thick paper, Slowm2 = 06hm2 = 65h
Paper feed
adjustment
Paper feeding is adjusted. The setting value is operated
as an absolute value.
• -0.7% <= ±0% <= 0.7%SN m1 = 04h
• If -0.7%SN m2 = 1Fh
• If 0% SN m2 = 65h
• If 0.7%SN m2 = ABh
Eject paper
roller set
Select eject paper roller. If auto is selected, it is operated
as cut sheet: sheet Star Wheel, roll paper: none
• SN
m1 = 85h
• SHEETm2 = 01h
• ROLL NOMALm2 = 03h (None)
• AUTO m2 = 00h
• ROLL CURLEDm2 = 02h
Ink drying time
Ink drying time for each pass is set. The carriage stops at
the right/left sides of paper for setting time. (DR m1 = 40h)
0 sec. ~ 10000 mm/sec (unit 100mm/sec)
*2
0000h ~ 01F4h
Paper suction
Paper suction is set to make paper stable on the platen.
Select "-1" for thin paper (film etc.), which is difficult to
feed and lower the suction according to thickness rate.
• SN
m1 = 05h
• -1
m2 = 1Ah (50%)
• -3
m2 = 06h (10%)
• Standardm2 = 33h (100%)
• -2
m2 = 10h (30%)
• -4
m2 = 04h (6%)
MW print
adjustment
Micro weave mode is adjusted.
When print speed has priority, lower the setting value.
When quality has priority, raise the setting value.
Table 1-34 "MW print adjustmen List"(p75)
for MW modes that can be selected by MW
print adjustment.
Summary of Contents for Stylus Pro 4800 Portrait Edition
