background image

Rev. B

   

iii

UB-U09 Developer's Guide

Confidential

CONFIDENTIALITY AGREEMENT

BY USING THIS DOCUMENT, YOU AGREE TO ABIDE BY THE TERMS OF THIS AGREEMENT.  PLEASE RETURN 
THIS DOCUMENT IMMEDIATELY IF YOU DO NOT AGREE TO THESE TERMS.

This document contains confidential, proprietary information of Seiko Epson Corporation or its affiliates. You 
must keep such information confidential. If the user is a business entity or organization, you must limit disclosure 
to those of your employees, agents and contractors who have a need to know and who are also bound by 
obligations of confidentiality.

On the earlier of (a) termination of your relationship with Seiko Epson, or (b) Seiko Epson’s request, you must 
stop using the confidential information. You must then return or destroy the information, as directed by Seiko 
Epson.

If a court, arbitrator, government agency or the like orders you to disclose any confidential information, you must 
immediately notify Seiko Epson. You agree to give Seiko Epson reasonable cooperation and assistance in the 
negotiation.

You may use confidential information only for the purpose of operating or servicing the products to which the 
document relates, unless you obtain the prior written consent of Seiko Epson for some other use.

Seiko Epson warrants that it has the right to disclose the confidential information. SEIKO EPSON MAKES NO 
OTHER WARRANTIES CONCERNING THE CONFIDENTIAL INFORMATION OR ANY OTHER 
INFORMATION ON THE DOCUMENT, INCLUDING (WITHOUT LIMITATION) ANY WARRANTY OF TITLE 
OR NON-INFRINGEMENT. Seiko Epson has no liability for loss or damage arising from or relating to your use of 
or reliance on the information on the document.

You may not reproduce, store or transmit the confidential information in any form or by any means (electronic, 
mechanical, photocopying, recording, or otherwise) without the prior written permission of Seiko Epson.

Your obligations under this Agreement are in addition to any other legal obligations. Seiko Epson does not waive 
any right under this Agreement by failing to exercise it. The laws of Japan apply to this Agreement.

Cautions

No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any 
means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of 
Seiko Epson Corporation.

The contents of this document are subject to change without notice. Please contact us for the latest information.

While every precaution has been taken in the preparation of this document, Seiko Epson Corporation assumes no 
responsibility for errors or omissions. 

Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties 
for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or 
abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding theU. S.) 
failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options 
or any consumable products other than those designated as Original EPSON Products or EPSON Approved 
Products by Seiko Epson Corporation.

EPSON

®

 and ESC/POS

®

 are registered trademarks of Seiko Epson Corporation

Summary of Contents for UB-U09

























Reviews: