background image

QuadroM-E1/T1 Manual I: Installation Guide 

Hardware Overview 

 

 

QuadroM-E1/T1;  (SW Version 5.2.x) 

 

QuadroM-E1/T1’s Front Panel LEDs 

 

 

Fig. I-4: QuadroM-E1/T1's Front Panel LEDs 

 

BUSY 
green 
(Status of the CPU) 

on: device is booting 
off
: No power  
blinking: activity 

INFO 
yellow 
(System information) 

on: device is booting 
off: no information 
blinking: an event occurred that was speci-
fied in Event Management 

FAULT 
red 
(System status) 

on device is booting/ error 
off: no error 
blinking: system unusable 

GP 
green 

undefined 

LAN  
green 
(Status of the LAN interface) 

on: link ok 
off: no link 
flickering: traffic on the link 

WAN  
green 
(Status of the WAN interface) 

on: link ok 
off: no link 
flickering: traffic on the link  
 

Line1  
green 
(Status of the E1/T1 trunk 1) 

on: frame synchronization is ok 
off: frame synchronization is not ok or link is 
down  

Line2  
green 

(Status of the E1/T1 trunk  2, not used for 
Single QuadroM-E1/T1) 

on: frame synchronization is ok 
off: frame synchronization is not ok or link is 
down  

 
 
LED Indication during a firmware update 

A firmware update is indicated by the red (Fault) and yellow (Info) LED. Both will blink si-
multaneously for about five minutes while the firmware is updated. The QuadroM-E1/T1 will 
then re-boot automatically showing the boot LED sequence. 

 
LED Indication during a boot sequence 

A boot sequence is indicated as follows: The red Fault LED will glow for a few seconds, then 
the yellow Info LED will glow for another four or five minutes while the green Busy LED is 
blinking. Once the Info LED is off, the boot sequence has been completed successfully.

Summary of Contents for QuadroM-E1
























































Reviews: