3. INSTRUCTION FOR USE
When the product is plugged and push the ON/OFF (0/I) button located at the back of the
appliance,the buzzer “beeps” and the screen flashes for 3s, then in the standby mode. Push
again, if you want to switch off.
In standby mode,you can set the day and time.
SET THE CURREN DAY
Press
SET
, the day icon
（
1 2 3 4 5 6 7
）
flashes. Use + and - to set current day. Then press
OK
,
it will save and enter into next step automatically for hour setting.
SET THE CURREN HOUR
The hour icon 01:00 flashes. Use + and - to set hour. Then press
OK
, the minute icon
00:01flashes. Use + and - to set minutes. In the end ,press
OK
to confirm and save automatically.
Manual mode:
Press ,start at 2000W (show on screen), you can do the following:
1) SET TEMPERATURE
Press
SET
, setting temperature flashes 20 (default temperature setting is 20°C), use + and - to
set and press
OK
to confirm(selected temperature range 5°C - 40°C).
2) CHANGE POWER
In Manual mode, press to set the power in following order: 2000W( )-1000W( )
-Fan ( ). Press again, the power changing will repeat the cycle.
Window mode(ONLY work during manual program):
Press to turn on open-window detection:
During open-window detection mode,once the ambient temperature drops 5-10
℃
within 10
minutes, then the product will stop working within 30 minutes and enter into stand by mode.
Press the button again to turn off open-window detection.
WEEKLY PROGRAM SETTING (PROGRAM MODE)
Weekly program explain:
1. It can set day by day from Monday to Sunday. And for each day, it can set 2 working periods
(P1/ P2).
2. The product works at full power(2000W) during weekly program.
3. Body sensor only works in weekly program if turn on.
WEEKLY PROGRAM SETTING:
In STANDY MODE: Press for 3 seconds, it enters into WEEKLY PROGRAM setting,the icon
flashes on the screen until complete the whole setting. And the day icon (1 2 3 4 5 6 7) flashes,
use + and - to select the day, P1 shows in screen (The wake up time for the initial setting, the
time shows “OFF”. Press , the time become and can start to set ). Press
OK
, it enters
into next step - wake up time setting: the hour flash (use + and - to set(23-hours). Then press
OK
, it enters into next step - minutes setting: the minute icon flashes. Use + and – to
set minute(0-58 minutes). Then press
OK
, it enters into next step - temperature setting: setting
temperature flashes 20 (default temperature setting is 20°C ), use + and - to set(selected
temperature range 5°C - 40°C). Press
OK
, it enters into next step - OFF time setting:
the hour flash use + and - to set(23-hours). Then press
OK
, it enters into next step - minutes
setting: to minute setting, the minute icon flashes. Use + and – to set minute (0-59
minutes). Press
OK
to confirm and it automatically enter to next working period. In this cycle,
you can set 7 days on/off timer.
The will be displayed on the working status. If you want to turn off the weekly program,
press to turn off,and the screen will disappear.
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
Children of less than 3 years should be kept away unless continuously
supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
CAUTION - Some parts of this product can become very hot and cause
burns. Particular attention has to be given where children and vulnerable
people are present.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
CAUTION:
In order to avoid a hazard due to inadvertent resetting of the
thermal cutout, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
WARNING:
In order to avoid overheating, do not cover the
heater.
The heater must not be located immediately below a socket-outlet.
WARNING:
In order to avoid a hazard for very young children, this appliance
should be installed so that the lowest heated rail is at least 600 mm above the
floor.
Appliance is to be supplied through a residual current device (RCD) having a
FR
ES
PT
IT
EL
PL
RU
UA
RO
EN
63
FR
ES
PT
IT
EL
PL
RU
UA
RO
EN
64
2. INSTALLATION
•
•
•
rated residual operating current not exceeding 30 mA.
Means for disconnection having a contact separation in all poles must be
incorporated in the fixed wiring in accordance with the wiring rules.
Regarding the information for the installation and the connection of the
appliance, please refer to the relevant paragraphs below.
Concerning installation information, please refer to the chapter<<
Installation>> and <<Fixation of the appliance on the wall>>.
Choose a wall on which there is enough space:
Use a Φ6 drill to drill 6 holes according to following positions:
Fit the pegs from the accessory bag in these holes.
Detach the up-hook from the back of the appliance and put it in the position
of the five pegs at the bottom. Fix the up-hook on wall with five ST4X35
screws.
Hang the appliance on wall with a ST4X35 screw on the peg above.
Tighten four M5X12 screws on the right side and one ST4X12 screw on the left
side to fix the appliance.
Connect the two conductors of the supply cable to a connection box in
respecting the polarities as below:
- Live: Brown
- Neutral: Blue
Warning: this product shall be installed in the volumes 2 only according
the national wiring rules (For France NF C 15-100).
Note:
We suggest that you to contact a professional electrician for assistance.
1.
2.
3.
4.
5.
6.
Fixation of the appliance on wall
