21
20
ASSEMBLY
01
UNPACKING
Unpack all parts and lay them on a flat, stable surface.
• Remove all packing materials and shipping devices, if applicable.
• Make sure the delivery contents are complete and free of any damage. If you find that parts
are missing or show damage do not use the product but contact your dealer. Using an
incomplete or damaged product represents a hazard to people and property.
• Ensure that you have all the accessories and tools needed for assembly and operation.
This also includes suitable personal protective equipment
WARNING!
The product and the packaging are not children’s toys!
Children must not play with plastic bags, sheets and small parts! There is a
danger of choking and suffocation!
03
ASSEMBLY
MOUNTING AND ADJUSTING THE BIKE HANDLE (FIG. A)
Align the bike handle (7) with the bracket on the shaft.
Securely attach the bike handle (7) on the upper shaft (8) by fasten the wing bolt (6).
SHAFT ASSEMBLY (FIG. B)
Align the shaft-release button (9a) on the lower shaft (10) with the fixing hole on the
coupler (9)
Push down the shaft-release bottom (9a) and insert the lower shaft (10) into the coupler
(9). Ensure the button securely locates in the hole.
Pull the lower shaft (10) to verify it is securely locked into the coupler (9). If not, rotate
the lower shaft (10) from side to side in the coupler (9) until the shaft-release button (9a)
snaps into place.
Tighten the wing bolt (9b) fully.
MOUNTING THE GUARD (FIG. C1, C2)
Blade guard
Align the blade guard mounting holes with the assembly holes on the lower shaft (10)
and then lock it with the two screws (Fig. C1) using hex key tool (28).
Trimmer guard
Use the same method to attach the trimmer guard (18) as above.Then attach the cover
on the trimmer guard (18) with other two screws (Fig. C2).
WARNING!
Never use the product without properly fitted guard!
WARNING!
For all work with the machine, a correct protection guard (for
brush cutting or for grass trimming application) must always be mounted
carefully.
BRUSH CUTTING BLADE (FIG. D1-D2)
Make sure that the blade guard (14) has been attached properly.
Rotate the spindle until the hole on backing flange (20) is aligned with the hole of spindle
locking in the gear head (12).
Insert the hex wrench (28) into the hole to lock the spindle (Fig. D1).
Loosen the nut (24) clockwise and remove it together with the locking flange (23) using
multi function wrench (27).
Fit the cutting blade (13) onto the spindle ensuring that the directional arrows on the
blade guard (14) and the cutting blade (13) match. Ensure that the blade sits flush on the
extruded ring on the backing flange (20).
Place the locking flange (23) onto the cutting blade (13).
Secure the cutting blade (13) with the nut (24) by using the multi-function wrench (27) (Fig.
D2).
Remove the hex wrench (28).
TRIMMING HEAD (FIG. E1-E4 AND L1)
Make sure that the trimmer guard (18) has been attached properly.
Rotate the spindle until the hole on backing flange (20) is aligned with the hole of spindle
locking in the gear head (12).
Insert the hex wrench (28) into the hole to lock the spindle (Fig. E1).
Press the two release buttons (16) on the spool base and pull the spool retainer out (Fig.
L1, E2).
Pull off the bump knob (17)(Fig. E3).
Loosen the nut (24) clockwise and remove it together with the spool base (Fig. E4).
Remove the hex wrench (28).
For trimming head attaching,just operate as above steps inversely.
HARNESS (FIG. F1-F3)
The harness (26) helps the operator to carry the product.
