background image

1

/

2

 SHEET SANDER

GUARANTEE

This 

 product carries a Screwfix Direct Ltd guarantee of 24 months. If your 

product  develops  a  fault  within  this  period,  you  should  in  the  first  instance  contact 

Screwfix Direct Ltd on Freephone 0500 41 41 41.  If the fault occurs within the first 24 

months, you may return the goods for a full refund or we will repair or replace the goods 

if you prefer. When repair is not practical or identical goods are not available, alternative

goods of similar specification and quality will usually be provided but, failing this, you 

will be offered a partial or full refund depending on the time period since purchase. 

This guarantee specifically excludes losses caused due to:

- Fair wear and tear

- Misuse or abuse

- Lack of routine maintenance

- Failure of consumable items (such as batteries)

- Accidental damage

- Cosmetic damage

- Failure to follow manufacturer’s guidelines

- Loss of use of the goods

- Repairs attempted by anyone, unless authorised by Screwfix Direct Ltd.

This guarantee does not affect your statutory rights. This guarantee is only valid in the UK.

For further technical advice, spare parts or repair service (outside of guarantee) please 

contact the customer helpline number on 0845 607 6380 

Congratulations  on  your  purchase  of  a  quality  power  tool  from  Screwfix 

Direct Ltd. This product should give you reliable service but for your peace of 

mind this 

 power tool does carries a 24-month guarantee, the terms 

of which are detailed below.

If this product develops a fault within the guarantee period contact Screwfix 

Direct Ltd on Freephone 0500 41 41 41. 

Please retain this handbook in case you need to refer to safety, care or guarantee 

information in the future.

SFX-ERB406-M-050608.indd   3

2005-6-8   14:49:54

Summary of Contents for ERB406

















Reviews: