background image

 

 

 

 

3.

 

Under the Lower Worksurface, plug the male end of the USB cable (from Key- 

board) into the female USB receptor on the Power Channel® and the keyboard 
connection is complete. (Fig. 12)

 

 

 

Lower work surface

 

Top tier support shaft

 

 
 
 
 
 
 
 

 

Power Channel®

 

 

 
 
 
 

USB Cable

 

(From USB Keyboard)

 

 

 

Fig. 12

 

 
 

Section 5 - Worksurface height adjustment 

 

Your Ergonomic Products Workstation is height adjustable. To adjust the worksurface height to your personal 
preference, read the following section.

 

 

To Adjust:

  Loosen the Height Adjust Set Screw on the Workstation Support Post Coupler 

and raise or lower the worksurface (in one inch increments) to the desired height and then 
re-tighten the set screw. (Fig. 13)

 

 

 
 
 
 
 

Workstation 
support Post 
coupler

 

              
                  

Workstation support  

                               Post 

 

 
 
 
 
 
 
 
 

 

 

       Height adjust set screw

 

                 

Height adjustment detent(s)

 

 

Fig. 13

 

Important: The height adjustment is only complete when the set screw is in contact with a 
height adjustment detent.

 

Summary of Contents for D1 Workstation
















Reviews: