background image

 

Sana comfort 150 and 250 REHA 

 

 

Article no.: 2.520064 rev.: b 

Page 6 of 24 

 

2.4

 

Technical data 

Bicycle ergometer with blood pressure measurement in accordance with DIN 13405 /DIN VDE 0750-238. 

 

Braking principle  Computer-controlled brakes with permanent measurement of 

torque. Braking performance is independent of revolutions per min-

ute. 

Power range  1 to 999 watts 

Load range  independent rpm range 20 till 999 Watts 

Range of revolutions  30 to 130 rpm for pedals 

Load precision  3%, not less than 3 watts (in the independent rpm range) 

Load parameters  1.

 

In keeping with set internal load program 

2.

 

Parameters from external master unit over interface, in 1 watt 

steps. 

3.

 

Manual in 5-watt and 25-watt steps 

Load software  5 freely programmable ergometry programs 

1 automatically controlled pulse-steady-state program 

Time intervals  1 min to 99 min 

Display  Graphic LCD with 320 x 240 pixels, CCFT background lighting 

Blood pressure measure-

ment for 250 

Indirectly, with a specific, modified measuring system based on R-R, 

and computer analysis including maximal suppression of artefacts 
during ergometry. Automatic deflation rate of 3 mmHg/pulse. Meas-

uring range 40 - 300 mmHg. 

Pulse measurement  With a blood pressure unit or an optional Polar pulse monitoring 

system; pulse rate 35 - 240 

Horizontal seat adjustment  Continuously variable on a slope, special seat for heights between 

150 and 210 cm, electric drive. 

Maximal permissible 

patient weight 

250 kg 

Long-term accuracy  Torque equalisation at any time with weight 

Power supply  230 VAC 50–60 Hz, 115 VAC 50–60 Hz 

The unit is suitable for use in networks according to CISPR 11, 
group 1, class B. 

Electric inputs/outputs  RS-232 (galvanically isolated) 

Base dimensions  40 x 130 cm 

Weight  74 kg 

2.5

 

Signs and symbols 

In this section, the signs and symbols used in connection with this device are explained: 

 

 

 

 

 

 

Mains operated, alternating current 

 

BF classified component 

 

93/42/EEC for medical products 0124 

DEKRA 

 

 

IPX0 

Potential equalisation connection (earth) 

 

Warning! Follow the instructions in the docu-

mentation. 

Protection class of the casing: IPX0 

Summary of Contents for Sana comfort 150 REHA


























Reviews: