background image

2/21

2

1

9a

8

7

13

2b

10

2a

6

5

3

9

4

11

12

16

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

15

14

EN

888-24-092-G-02 rev. H • 05/11

Features & Specifi cations

WARNING

IMPACT HAZARD!

MOVING PARTS CAN CRUSH AND CUT.

Minimize Lift Tension BEFORE:

· Removing Mounted Equipment.
· Shipping Cart
· Storing Cart

To Minimize Lift Tension
1.  

Lower worksurface to lowest position.

2.  

Turn adjustment nut at top of riser 

counterclockwise until it stops 
(Adjustment may require 40-60 revolutions).

Failure to heed this warning may result in 

serious personal injury or property damage!

For More information and instructions refer to product 

guide at  

http://4support.ergotron.com

 or contact 

Ergotron Customer Care at 

1-800-888-8458.

822-052

14mm (9/16”)

Worksurface:  

2a.

 User Interface 

2b.

 Autolock Drawer Keypad

Secure Storage for Laptop, Thin Client or CPU up to 3.75" (95 mm) thick

Front Handle

Height Adjustment Brake

Ready On button wakes computer when set to hibernate mode

USB Hub connects keyboard and mouse USB cables

Keyboard tray slides out, tilts and allows for right or left mousing with attached mouse holder

Keyboard Light under Front Handle

9a.

 Keyboard Light Switch

Cable Management and Storage for excess cables and power supplies

Storage Basket and Rear Handle

Front Locking Casters

Auto-Lock Drawer (see page 3 for drawer confi gurations)

Quick Reference Card

Power Cord Hook

Height Adjustable LCD Mount attaches LCDs or tablet PC's with 75x75 or 100x100mm mounting interface

BATTERY 

LEAD

-20 °C
-   4 °F

  50 °C
122 °F

Relative

Humidity 

Range

5-95% rH

10 °C
50 °F

  29 °C

 86 °F

Relative

Humidity 

Range

5-95% rH

Operational

Storage

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme 
NMB-003 du Canada.

FCC Compliance Statement 

The cart has been tested and found to comply with the limits 
for a Class A digital device, pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated 
in a commercial environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and 
used in accordance with the instruction manual, may cause 
harmful interference to radio communications. Operation of 
this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct 
the interference at his own expense.

Changes or modifi cations not expressly approved by 
Ergotron, Inc. could void the user’s authority to operate the 
equipment.

Please contact Ergotron for complete EMC compatibility 
information.

Power System

 - (see page 3 for additional information)

The StyleView AC Power System allows your power supply 
to travel with the cart. The Power System is integrated in the 
base of the cart and comes standard with 2 batteries, power 
module, User Interface (UI), outlet box and power cord.
•  User Interface (UI): Allows power system output to be 
turned on or turned off , monitors battery charge remaining, 
and provides low battery charge audible alarm.
•  Two 33 Ah Sealed Lead Acid, Absorbed Glass Mat, 12VDC 
batteries.
•  The minimum operational temperature is 10°C (50°F) and 
the maximum operational temperature is 29°C (86°F). The 
recommended humidity range for operation is 5-95% rH.
•  The recommended cart storage temperature is 15°C (59°F).  
At this temperature, the battery’s age-related capacity loss is 
minimized.  The minimum storage temperature is -20°C (-4°F) 
and the maximum storage temperature is 50°C (122°F). The 
recommended humidity range for storage is 5-95% rH.

Summary of Contents for StyleView SV32






















Reviews: