background image

Sump Cleaner

23

W  

e  

e  

 l 

 y

y

 

s

12 

 

s

Maintenance

Schedule for Electric Motor  

Sump Cleaners

Maintenance Log 

Date placed into service:

                                         

Record date of service below:  

                                         

Inspect suction and discharge hoses;  

replace as needed
Inspect filter basket sleeve; replace as need-

ed. Inspect basket lifting rings for corrosion
Inspect tank for sludge buildup; clean as 

needed
Check blower oil level (add SAE-40  

non-detergent oil as needed)
Grease blower; (use No. 2 bearing grease - 

500 hours)
Grease motor bearings (use No. 2 bearing 

grease)
Grease wheels and casters; (use No. 2  

bearing grease)
Change blower oil; (use SAE-40  

non-detergent oil - 1500 hours)
Drain blower mufflers if equipped with  

optional sound reduction mufflers (drain  

plug is on lower end of muffler)

3-phase Maintenance Schedule

9.  To discharge clean fluid to refill a machine 

sump:

 close the suction inlet ball valve V1, attach 

the 1-1/2" hose to the discharge port, place the 
discharge nozzle in the machine sump, push the 
DISCHARGE button, and depress the discharge 
hose nozzle valve. 
A.  Be sure the suction inlet ball valve is fully  
 

closed before operating in the DISCHARGE  

 mode! 

B. IMPORTANT! Be sure the suction inlet ball  
 

valve is fully closed or fully open, depending  

 

on the desired operation (closed-discharge,  

 

open-suction). Failure to do so will allow  

 

particulates to enter the valve seat and  

 

seize the valve. 

C. Stop the motor as soon as fluid stops passing  
 

through the hose. 

D.  The sump cleaner will discharge all but  
 

about an inch of fluid in the bottom of the  

 

compartment. This is unimportant if the  

 

compartment cleaner is used for one type  

 

of coolant only. If different coolants are to  

 

be handled in that compartment, remove  

 

its drain plug to empty it completely. 

3-phase Electric Dual Tank
Operation 

(contd.)

Summary of Contents for FJ-310A





























Reviews: