background image

12

3BA00253-01 

 2021-05-17 

 Rev. 1 

Ersa i-CON 1V & i-CON 1VC

8. 

Warranty

© 4/2021, Ersa GmbH, 3BA00253-01

Heating elements and soldering or desoldering tips are wearing parts that are not cov

-

ered by the warranty. Material- or production-related defects must be reported through 
notification by submitting the purchase receipt before the return of the goods, which 

must be acknowledged; the purchase receipt is then to be enclosed with the return of 
the goods.

Ersa drew up this instruction manual with utter care. However, no guarantee can be 
granted for its contents, completeness and the quality of the information provided there

-

in. The contents have been carefully updated and adapted to current conditions.
All data as well as any product and process information published in this instruction man

-

ual were ascertained by us to the best of our knowledge, using the most cutting-edge 
technical tools. This information is nonbinding and does not relieve the user of the 

responsibility to check themselves the equipment before using it. We shall not be held 

liable for any infringement of third-party property rights due to applications and proce

-

dures without prior express written confirmation. We reserve the right to make technical 

changes as part of a product improvement.

As far as legally possible, liability shall be precluded in cases of any direct, consequential 
and third-party damage resulting from the purchase of this product.

All rights reserved. This user guide may not be reproduced, changed, transferred or 

translated into another language, in whole or in part, without the written approval of 

Ersa GmbH.

Warranty

Summary of Contents for i-CON 1V















Reviews: