background image

Models 110X, 210X, 310X, 360X, 410X 

Safety and operating instructions 

 

 
 

Drugs, alcohol or medication 

  

WARNING 

Drugs, alcohol or medication 

Drugs, alcohol or medication may impair your 
judgment and powers of concentration. Poor 
reactions and incorrect assessments can lead to 
severe accidents or death. 

Never use the machine when you are tired or 

under the influence of drugs, alcohol or 
medication. 

No person who is under the influence of drugs, 

alcohol or medication may operate the machine. 

 

Carrier, precautions 

 

 

Before using or transporting the carrier with the 
hydraulic breaker attached, carefully read the carrier 
manufacturer's safety regulations and operating 
instructions. 

Make  sure  that  the  carrier  is  equipped  with 
adequate protective features, including a protective 
screen in front of the operator. 

The hydraulic breaker must only be mounted on a 
carrier with sufficient load capacity. 

Carriers without sufficient load capacity will not 
provide the required degree of stability and could 
even fall over during hydraulic breaker use, causing 
injury and damage. 

 

Installation, precautions 

 

 

Hydraulic system 

   

DANGER 

Compressed gas, explosion 

hazard 

The integrated piston accumulator is pressurized 
even when the hydraulic system is shut off. To 
dismount the accumulator without first releasing 
the nitrogen gas can cause serious personal injury 
or death. 

Fill the integrated piston accumulator with 

nitrogen (N 

2

) only. 

 

   

WARNING 

Hydraulic oil at high 

pressure 

Thin jets of hydraulic oil under high pressure can 
penetrate the skin and cause permanent injury. 

► 

Immediately consult a doctor if hydraulic oil has 

penetrated the skin. 

Never use your fingers to check for hydraulic fluid 

leaks. 

► 

Keep your face away from any possible leaks. 

   

WARNING 

Hydraulic oil 

Spilled hydraulic oil can cause burns, accidents 
due to slippery conditions and will also harm the 
environment. 

Take care of all spilled oil and handle it according 

to your safety and environmental regulations. 

Never dismount the hydraulic machine when the 

hydraulic oil is hot. 

Never run any hydraulic lines for attachment of 

the hydraulic machine through the 

driver’s cab. 

 

   

CAUTION 

Skin eczema 

Hydraulic oil can cause eczema if it comes in contact 
with the skin. 

► 

Avoid getting hydraulic oil on your hands. 

Always use protective gloves when working with 

hydraulic oil. 

► 

Wash hands after contact with hydraulic oil. 

 

Assembly or disassembly 

   

WARNING 

Moving parts 

Risk for leaking oil and personal injury, such as 
crushed hands and fingers. 

► 

Never check bores or passages with hands or 

fingers. 

► 

Any  boom  movements  must  only  be  done  in 

cooperation  with  the  personnel  mounting  the 
hydraulic breaker. 

► 

If  the  hydraulic  breaker  is  mounted  on  a  quick 

hitch  coupling,  make  sure  it  is  locked  securely 
and  all  risks  of  the  hydraulic  breaker  coming 
loose are eliminated. 

 

Operation, precautions 

 

 

   

DANGER 

Explosion hazard 

If an insertion tool comes into contact with 
explosives or explosive gases, an explosion could 
occur. When working on certain materials and when 
using certain materials in machine parts, sparks and 
ignition can occur. Explosions will lead to severe 
injuries or death. 

Never operate the machine in any explosive 

environment. 

► 

Never use the machine near flammable materials, 
fumes or dust. 

► 

Make sure that there are no undetected sources 

of gas or explosives. 

Summary of Contents for 110X

































Reviews: