background image

 

16 

                                              PARTS INFORMATION 

 

 

 

 

 

 

ITEM 

QTY 

PART NO.  DESCRIPTION 

STOCK NO.  

400600 

GRINDER MOUNT MINI W/A 

  

400601 

FRAME SWING MINI SG W/A 

  

400602 

FRAME ARM MINI SG W/A 

  

400604 

WHEEL GRINDER 16 ASSM 

  

400605 

SHIELD MINI STUMP GRINDER W/A 

  

311657 

SHIELD RUBBER 

  

310198 

PIN 1.00 X 7.63 W/A 

  

311605 

PIN 1.25 X 6.75 W/A 

  

313460 

PIN 1.00 X 2.75 W/A 

  

10 

400041 

PIN 1 X 4 W/A 

  

11 

316026 

PIN 1 X 5 W/A 

  

12 

314079 

PIN 1.25 X 5.50 W/H Z 

  

13 

400633 

SHEILD COUPLER MSG PAINTED 

 

15 

13214 

BOLT HEX 

1/2 X 2-3/4 NC GR 5 

14 

314120 

GEARBOX RC51 PNT (32oz of 80W-90)   

18 

314015 

COUPLER BM 1.25 X 1.38 

  

19 

15 

37212 

NUT HEX LOCK 

3/8 NC 

20 

103116 

BOLT HEX 

3/8 X 1 NC GR 5 

23 

33220 

WASHER FENDER  

3/8 X 1 1/2 

24 

13107 

BOLT HEX 

3/8 X 1-1/4 NC GR 5 

25 

13207 

BOLT HEX 

1/2 X 1-1/4 NC GR 5 

26 

0167011 

NUT FLG TOP-LOCK 

1/2 GR8 

27 

37214 

NUT HEX LOCK 

1/2 NC 

28 

22888 

BOLT FLNG 12PT 

1/2 X 1-3/4 NC GR 9 

29 

13113 

BOLT HEX 

3/8 X 2-1/2 NC GR 5 

30 

13309 

BOLT HEX 

5/8 X 1-1/2 NC GR 5 

31 

37216 

NUT HEX LOCK 

5/8 NC 

32 

12 

311629 

TOOTH HOLDER SG BLANK 

  

33 

12 

311626 

TOOTH SG RIGHT 

  

34 

12 

311627 

TOOTH SG LEFT 

  

35 

12 

311677 

TOOTH HOLDER SG THREADED 

  

36 

24 

311630 

BOLT SOCKET HEAD CAP SCREW 

5/8 X 2-1/4 NF 

37 

400000 

MOUNT FRAME TORO MINI W/A 

OPTIONAL MOUNT PACKAGE 

 

400001 

MOUNT FRAME ASV MINI W/A 

OPTIONAL MOUNT PACKAGE 

 

400002 

MOUNT FRAME BC MINI W/A  

OPTIONAL MOUNT PACKAGE 

 

300283 

MOUNT FRAME UNIV MINI W/A 

OPTIONAL MOUNT PACKAGE 

 

330622 

MOUNT FRAME AVANT MINI W/A 

AVANT ADPT MNT PKG 330753 

38 

15209 

BOLT HEX 1/2 X 1-1/2 NC GR 8 

MOUNTING PACKAGES 

39 

0167011 

NUT FLG TOP LOCK 1/2 NC GR 8 YZ 

MOUNTING PACKAGES 

 

Summary of Contents for 900549

























Reviews: