background image

 

15 

LIMITED WARRANTY 

 

Erskine Attachments LLC warrants each new machine manufactured by us to be free from defects 
in material and workmanship for a period of twelve (12) months from date of delivery to the original 
purchaser. 
 
Our  obligation  under  this  warranty  is  to  replace  free  of  charge,  at  our  factory  or  authorized 
dealership, any part proven defective within the stated warranty time limit. 
 
All parts must be returned freight prepaid and adequately packaged to prevent damage in transit. 
 
This warranty does not cover: 

1.

New products which have been operated in excess of rated capacities or negligence 

2.

Misuse, abuse, accidents or damage due to improperly routed hoses 

3.

Machines which have been altered, modified or repaired in any manner not authorized 
by our company 

4.

Previously owned equipment 

5.

Any  ground  engaging  tools  in  which  natural  wear  is  involved,  i.e.  tooth  tips,  cutting 
teeth, etc 

6.

Normal maintenance 

7.

Fork tines 

8.

Hydraulic motors that have been disassembled in any manor 

 
In  no  event  will  the  Sales  Representative,  Dealership,  Erskine  Attachments  LLC,  or  any  other 
company affiliated with it or them be  liable for incidental or consequential damages or injuries, 
including but not limited to the loss of profit, rental or substitute equipment or other commercial 
loss.  Purchaser’s sole and exclusive remedy being as provided here in above. 
 
Erskine Attachments LLC must receive immediate notification of defect and no allowance will be 
made for repairs without our consent or approval. 
 
This warranty is in lieu of all other warranties, express or implied by law or otherwise, and there 
is no warranty of merchantability or fitness purpose. 
 
No  agent,  employee,  or  representative  of  Erskine  Attachments  LLC  has  any  authority  to  bind 
Erskine Attachments LLC to any warranty except as specifically set forth herein.  Any of these 
limitations excluded by local law shall be deemed deleted from this warranty; all other terms apply. 
 
This  warranty  may  not  be  enlarged  or  modified  in  any  manner  except  in  writing  signed  by  an 
executive officer of Erskine Attachments LLC to improve its products whenever it is possible and 
practical  to  do  so.    Erskine  Attachments  LLC  reserves  the  right  to  make  changes  and  or  add 
improvements at  any time without  incurring any obligation to make such changes or  add such 
improvements to products previously sold.  
 

 

 

 

 

 

 

 

 

 

Erskine Attachments LLC 

P.O. Box 1083 Alexandria, MN 56308 

Phone (218) 435-4045 Fax (218) 435-5293 

Summary of Contents for LS 24

















Reviews: