background image

SECTION  5

         TROUBLESHOOTING

21

The  cause  of  control  malfunctions  can  be  found  by

referring to the sequence of operations and electrical

schematic diagram (Figure 5-1) and checking  the vari-

ous components.  A volt-ohmmeter will be necessary for

some of these checks.

Voltages  in  plasma  cutting  equipment  are  high

enough to cause serious injury or possibly death. Be

particularly careful around equipment when the cov-

ers are removed.

NOTE

Before checking voltages in the circuit, disconnect the

power from the high frequency generator to avoid dam-

aging your voltmeter.

5.1TROUBLESHOOTING

ELECTRIC SHOCK CAN KILL! Be sure that all pri-

mary  power  to  the  machine  has  been  externally

disconnected. Open the line (wall) disconnect switch

or circuit breaker before attempting inspection or

work inside of the power source.

Check the problem against the symptoms in the follow-

ing troubleshooting guide.  The remedy may be quite

simple.  If the cause cannot be quickly located, shut off

the input power, open up the unit, and perform a simple

visual  inspection  of  all  the  components  and  wiring.

Check for secure terminal connections, loose or burned

wiring or components, bulged or leaking capacitors, or

any other sign of damage or discoloration.

5.2TROUBLESHOOTING GUIDE

A. Power Light (PL1) does not come on.

1. Visually inspect the machine for any damage.

2. Check if the cooling fan is running. If not, then check the following :

a. Check if the machine power cord is plugged to the input power receptacle.

b. Measure the input power at the receptacle. If not present, then check the wall

disconnect switch and it’s fuses.

c. Check Fuse (F1). If fuse is ok, then check the input circuit breaker (CB1) for proper operation. Re-

place if defective.

3. If above items check OK , the problem is internal.  Send unit to an Authorized Repair Station for repair.

a. If the cooling fan is running, then measure voltage between pins P2-11 and P2-14of the control

board (should be 115 VAC). If there is no voltage, then replace transformer T2.

b. If the voltage is present, then the pilot light may be burnt out.

B. No Air Flow

A. Check air inlet supply.  Unit requires 320 CFH at 65 psig.

B. Check air hose and connections. Tighten if leaking.

C. Does air flow when “air test” switch  is in test position?

a. If not, check torch consumables, replace if necessary.

b. If above items check OK , the problem is internal.  Take unit to an Authorized Repair Station for repair.

Summary of Contents for PCM-875

















































Reviews: