background image

 

11

80.  When the screen displays 

Insert a blank ballot stock paper

, place 

completely blank ballot stock into the Ballot Feed Tray. After inserting the 
paper, the machine automatically begins printing the operation log, printing 
66 lines per page.  

 

Note

: Use only ballot stock paper in the ES&S AutoMARK™, any other 

paper will greatly increase the risk of paper jams. 

 

81.  If there are more than 132 entries in the operation log, you will need 
several pages.  After a page has been ejected from the ES&S AutoMARK™, 
if the message

 “insert a bank ballot stock paper” 

appears, insert another 

blank ballot stock into the Ballot Feed Tray.  Repeat this process until the 
message 

printing done

 appears.  

 

82.  Press 

Done

 to return to the main menu. 

 

83.  Turn the mode switch key to the 

Off

 position, remove, and store in a 

secure location. 

Note:  

The Operations Log File is stored on the Compact Flash Card, not the 

unit itself.

 

 

 

Remove the Test Ink Cartridge 

 

84.  Remove the screw or snap that secures the Rear Access Door.  Open the 
Door. 

85.  Remove the Test Ink Cartridge and using the screw or snap, re-secure the 
Rear Access Door. 

Note:  

The Test Ink Cartridge must be replaced on election day prior to the 

ES&S AutoMARK™ being turned on.  If the unit is turned on without the ink 
cartridge installed, this message will appear “

Alert!  A problem has occurred.  

Please notify an election official.  The print cartridge is missing.”

   

  

 

 

 

 

Summary of Contents for AutoMARK














Reviews: