Eschenbach 27773, User Manual

- 7 -

Gewährleistung

Wir gewähren im Rahmen der gesetzlichen 
Bestimmungen die Funktion des in dieser Anleitung 
beschriebenen Produktes in Hinsicht auf auftretende 
Mängel, die auf Fabrikationsfehler oder Materialfehler 
zurückzuführen sind. Bei Schäden durch unsachge-
mäße Behandlung, auch bei Beschädigung durch Fall 
oder Stoß, besteht kein Gewährleistungsanspruch. 
Gewährleistung nur durch Nachweis über Kaufbeleg!

English

You have purchased a quality product from the 
Eschenbach company that was “Made in Germany” 
using state-of-the-art manufacturing processes. We 
congratulate you on your decision.
The lens of high-quality, unbreakable PXM

®

 material 

is protected with a cera-tec

®

 hard coating. Scratch-re-

sistance is an important aspect of the quality and useful 
life of the lens.

Safety Instructions

X

Danger of glare and injury! 
Never look directly into the sun or other bright 
light sources using optical devices!

X

Do not look directly into the LED lamp!

X

Danger of fire! Lenses in optical devices can 
cause significant damage by focusing light to 
generate heat if handled or stored improperly. Be 
careful never to leave optical lenses lying in direct 
sunlight!

X

Protect your magnifying light from impacts, mois-
ture and excess heat. Never lay your magnifying 
light on a radiator or in direct sunlight.

X

The clamping screws 

r

 must be screwed in tight 

during use of the magnifying light!

X

The light source of this luminaire may only be 
replaced by the manufacturer or a service techni-
cian appointed by him or a comparable qualified 
person.

X

This magnifier lamp is only suitable for indoor use.

X

Never use the magnifying light near to containers 
filled with water!

X

Risk of tripping! Make certain that the power cord 
does not pose a danger. Do not wind the power 
cord around the magnifying light.

X

The product may only be used with the supplied 
mains adapter and its adapters.

X

Inform other persons, particularly children, of 
these dangers.

X

The screw 

s

 on the head joint may not be 

unscrewed.

The Operating Elements

q

 Lens

w

 Protective lid

e

 Control panel with: 

- On/Off button 
- Dimmer switch 
- Segment button

r

 Clamping screws

t

 Pivot arm

y

 Multi-range AC adapter with power cord 

(110-240V~/50-60Hz)

u

 Hole for pivot arm

i

 Clamping cylinder

o

 Table clamp

a

 Lens holder

s

 Screw head joint and upper arm joint (hex size 4)

Intended use

This product is intended exclusively for the enlarged 
display of details in the domestic and industrial sector.

Setting Up

1.  Screw the table clamp 

o

 to a table surface with 

the clamping cylinder 

i

.

2.  Plug the swivel stand 

t

 into the hole 

u

 in the ta-

ble clamp 

o

. Plug the appropriate country adapter 

into the mains adapter.

3.  Plug the AC adapter 

y

 into a properly connected 

power socket.

4.  Open the lens cover 

w

. The lens cover is only 

snapped on and can be removed completely if 

required.

5.  Press the large button in the middle to switch on the 

magnifier lamp. Press the left button to switch from 

segment lighting to ring lighting. To select one of the 

three intensity levels (100%, 60%, 40%), press the 

right button.

BDA_Lupenleuchte vario LED_2019.indd   7

13.06.2019   16:14:06