background image

All rights reserved. Reproduction as well as electronic duplication of this guide, complete or in part, requires the written consent of ESERA-
Automation or E-Service GmbH. Errors and technical modification subject to change. 

© 

ESERA-Automation, E-Service GmbH 2019 

www.esera.de 

Programming Manual Controller-Gateway-Station V1.0 R1.1 

Page 32 of 77 

8.5. 

„Data header“ 

Each data output of the 1-Wire Controller / 1-Wire Gateway starts with an abbreviation, e.g. "EVT" for Event.  
The chart below shows various "data headers". 

 

8.5.1. 

Event (EVT), data output 

Cyclically output data are 1-Wire data and "Keep Alive" messages (KAL). In order to be able to check that the 
data outputs are up-to-date, each cyclic data string contains the current time of the 1-Wire Controller / 1-Wire 
Gateway. By command the format of the data, the 1-Wire device name, can be selected from stored modes. 

8.5.2. 

1-Wire Controller / 1-Wire Gateway setting (CSE = Controller Setting) 

The data header "CSE" is put in front of the output of the 1-Wire Controller / 1-Wire Gateway settings. This allows 
your software to clearly recognize when this data was output. 

1-Wire Controller / 1-Wire Gateway setting data header: 

1_CSE|19:17:39

 

8.5.3. 

1-Wire Controller / 1-Wire Gateway info (CSI = Controller System Info) 

The data header "CSI" is put in front of the output of the 1-Wire Controller / 1-Wire Gateway. This allows your 
software to clearly recognize when this data was output. 

Info data header: 

1_CSI|19:15:02

 

8.6. 

Acknowledgement of receipt 

The 1-Wire Controller / 1-Wire Gateway sends an acknowledgement of receipt on each received command.  A 
text or numerical value can be output as confirmation by setting, ECHO 0 or 1. An echo or the numerical value "0" 
is output for an error-free command. 
If a command or part of a command is unknown or is outside the permitted value range, an error message in text- 
or number format is output. In each case, the first command part recognized as faulty will be output. 

Example data header „EVT|time“ 

Summary of Contents for 1-Wire Controller 2














































































Reviews: